Tri-Star TAC 17X Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 48

background image

Page 13

I

NTRODUCTION

Initial and periodic crimp verifications must be made in order to be certain a given TAC

is crimping properly. Once a TAC is set-up and crimp verification accomplished, the

device will normally complete hundreds of thousands of acceptable crimps before

indenter adjustment or replacement is necessary.

However, as in all precision equipment, something can malfunction, or the indenters

may inadvertently be subjected to a hard substance and the resulting crimp not meet

acceptable parameters. Therefore, it is recommended that the Crimp Verification

procedure be performed at least monthly. A system of "spot checks" can also be

established to verify acceptable crimps.

The Initial Crimp Verification should be performed immediately after the TAC has been

set-up (Section 2). Although the procedure is the same as all other verification tests, it

affords the user an opportunity to record data before the machine has been used

extensively. Read and understand Section 4, Operating Procedures, before performing

the verification. This paragraph details the procedure to verify TAC's with a fixed "G"

dimension and with an operator-selectable "G" dimension.

Perform the following steps to verify acceptable crimps:

W

ARNING

:

 

Before the funnel cover plate or the cylinder arbor cover plate is removed,

DISCONNECT the air supply from the sleeve valve. INJURY COULD RESULT ! !

Step 1.

Open the sleeve valve.

Step 2.

Disconnect the air supply from the sleeve valve.

Step 3.

Refer to Figure 3-1.

Step 4.

Remove the four button head socket cap screws securing the crimp

cylinder arbor cover plate.

C

RIMP

VERIFICATION

I

NITIAL

CRIMP

 

VERIFICATION

Arbor Plate

Removed

Figure 3-1: Crimp Cylinder Arbor, Open

Section 3

«
...
11
12
13
14
15
...
»

Содержание TAC 17X

















































Отзывы:

Нет отзывов

Похожие инструкции для TAC 17X

Бренд: Earlex Страницы: 20

Бренд: Gage Bilt Страницы: 24

Бренд: Gage Bilt Страницы: 24

Бренд: Gage Bilt Страницы: 24

Бренд: Textron Страницы: 4

Бренд: Matatakitoyo Torque Tools Страницы: 2

Бренд: DeWalt Страницы: 48

Бренд: Bossard Страницы: 16

Бренд: Lumax Страницы: 6

Бренд: BTI Страницы: 48

Бренд: Burndy Страницы: 2

Бренд: Burndy Страницы: 2

Бренд: Packers Kromer Страницы: 5

Бренд: Starrett Страницы: 4

Бренд: Meec tools Страницы: 9

Бренд: Meec tools Страницы: 11

Бренд: Von Arx Страницы: 21

Бренд: Sienci Labs Страницы: 86

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды