Tri-Star TAC 17X Скачать руководство пользователя страница 4

Страница: 4 / 48

Page 4

NTRODUCTION

Section 1

The Tri-Star Technologies TAC Series of Vibratory Feed Bowl Crimpers are

devices which automatically crimp loose electrical contacts to electrical

conductors. This operation manual is for the TAC-17X model. Figure 1-1 is a

photograph of a TAC-17X as viewed from the front (operator) side. This

photograph gives a view of the cabinet housing, the feeder-bowls, the

escapement systems, and the crimping system.

TAC-17X requires no lubrication or preventive maintenance except to

periodically change the air filter or drain it. Crimp acceptability should be

verified in accordance with the user's normal practices.

lndenters used in the TAC-17X are qualified to the M22520 specification and

are of the highest quality, to ensure a substantial quantity of acceptable

terminations.

Reasonable care must be exercised, however, to prevent any foreign matter,

particularly hard substances, from being crimped. lndenters might be damaged

if subjected to crimping anything other than the contact specifically intended.

Under normal operating conditions, however, the control system precludes the

TAC from crimping anything other than the specific contact for which the

equipment is tooled.

Содержание TAC 17X

















































Результаты поиска

Содержание TAC 17X

Отзывы:

Похожие инструкции для TAC 17X

Бренды по названию

Популярные бренды

Tri-Star TAC 17X, Руководство по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание TAC 17X

Отзывы:

Похожие инструкции для TAC 17X

Бренды по названию

Популярные бренды