Tri-Star TAC 17X Скачать руководство пользователя страница 24

Страница: 24 / 48

Page 24

The primary purpose of the Maintenance and Troubleshooting section of this manual is

to permit the user to perform required preventive maintenance, perform minor

adjustments and to correct minor malfunctions caused by incorrect/unacceptable

contacts.

Detailed instructions for adjusting and changing indenters are also given. In the event

it is necessary to replace an item which has become defective and for which there is

no specific disassembly instructions, use extreme care and/or consult the factory for

assistance.

The only preventive maintenance required for the TAC is the periodic inspection and

replacement of air filter F-1 and vacuum filter RFV-1. See Figure 6-2. Whenever it is

observed that filter F1 has accumulated moisture on the bottom, the moisture should

be drained by placing a cup or other container under F1, opening the sleeve valve,

opening the F1 drain, and draining the filter.

Do not allow the moisture to spray, drip or enter the cabinet when draining.

The vacuum filter RFV-1 can easily be located in-line between the transfer tip holder

and the TAC Control Unit. If the vacuum filter becomes clogged, decreased

performance with part detection at the transfer tip will be observed. When this situation

occurs, replacement of the vacuum filter is suggested. Please note the vacuum filter

orientation when removing, as the replacement filter must be installed with the same

orientation.

A vacuum circuit purge is also suggested any time a degraded performance of part

detection occurs. This can be done by performing the following steps: (Refer to Figure

6-1and 6-2).

Step 1.

Turn off air supply.

Step 2.

Unplug Power cord from wall outlet.

Step 3.

Remove the transfer tip from the tip holder.

Step 4.

Remove control unit cover plate.

Step 5.

Turn on air supply

Step 6.

Plug exhaust port of vacuum generator (VG-1) with finger for

approximately 10 seconds.

Step 7.

Repeat step 6 several times.

Step 8.

Turn off air supply.

Step 9.

Replace transfer tip to tip holder.

Step 10.

Replace control unit cover plate.

Step 11.

Plug power cord to wall outlet.

Step 12.

Turn on air supply at sleeve valve.

NTRODUCTION

AINTENANCE

TROUBLESHOOTING

Section 6

Содержание TAC 17X

















































Результаты поиска

Содержание TAC 17X

Отзывы:

Похожие инструкции для TAC 17X

Бренды по названию

Популярные бренды

Tri-Star TAC 17X, Руководство по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание TAC 17X

Отзывы:

Похожие инструкции для TAC 17X

Бренды по названию

Популярные бренды