Trenz Electronic TE0790 Скачать руководство пользователя страница 21

Страница: 21 / 27

TE0790 TRM

Revision: v.37

21 of 27

http://www.trenz-electronic.de

9 Technical Specifications

9.1 Absolute Maximum Ratings

Parameter

Min

Max

Units

Reference Document

3.3V

-0.3

FTDI FT2232H data sheet

VIO

-0.5

3.75

Lattice MachX02 Family data sheet

VBUS

4.75

5.25

USB2.0 Specification

Voltage on pins
A - H

-0.5

3.75

Lattice MachX02 Family data sheet

Storage
temperature

-40

100

°C

LED SML-P11 data sheet

Table 12:

Module absolute maximum ratings.

9.2 Recommended Operating Conditions

Parameter

Min

Max

Units

Reference Document

3.3V

2.375

3.6

Lattice MachX02 Family data sheet

VIO

1.14

3.6

Lattice MachX02 Family data sheet

VBUS

4.75

5.25

USB2.0 Specification

Voltage on pins
A - H

1.14

3.6

Lattice MachX02 Family data sheet

Operating
temperature

-40

°C

FTDI FT2232H data sheet

Table 13:

Module recommended operating conditions.

9.3 Operating Temperature Range

Industrial grade: -40°C to +85°C.

The TE0790 USB2.0 adapter board is capable to be operated at industrial grade temperature range.

Содержание TE0790























Результаты поиска

Содержание TE0790

Отзывы:

Trenz Electronic TE0790, Руководство пользователя, Страница: 21 / 27

Результаты поиска

Содержание TE0790

Отзывы: