TRENDnet TEG-S2400I - DATA SHEETS Скачать руководство пользователя страница 147

Страница: 147 / 149

Limited Warranty

TRENDware warrants its products against defects in material and workmanship, under

normal use and service, for the following lengths of time from the date of purchase.

TEG-S2600i – 5 Years Warranty

If a product does not operate as warranted above during the applicable warranty period,

TRENDware shall, at its option and expense, repair the defective product or part, deliver to

customer an equivalent product or part to replace the defective item, or refund to customer

the purchase price paid for the defective product. All products that are replaced will

become the property of TRENDware. Replacement products may be new or reconditioned.

TRENDware shall not be responsible for any software, firmware, information, or memory

data of customer contained in, stored on, or integrated with any products returned to

TRENDware pursuant to any warranty.

There are no user serviceable parts inside the product. Do not remove or attempt to

service the product by any unauthorized service center. This warranty is voided if (i) the

product has been modified or repaired by any unauthorized service center, (ii) the product

was subject to accident, abuse, or improper use (iii) the product was subject to conditions

more severe than those specified in the manual.

Warranty service may be obtained by contacting TRENDware office within the applicable

warranty period for a Return Material Authorization (RMA) number, accompanied by a copy

of the dated proof of the purchase. Products returned to TRENDware must be

pre-authorized by TRENDware with RMA number marked on the outside of the package,

and sent prepaid, insured and packaged appropriately for safe shipment.

WARRANTIES EXCLUSIVE

IF THE TRENDWARE PRODUCT DOES NOT OPERATE AS

WARRANTED ABOVE, THE CUSTOMER’S SOLE REMEDY SHALL BE, AT TRENDWARE’S OPTION,

REPAIR OR REPLACEMENT. THE FOREGOING WARRANTIES AND REMEDIES ARE EXCLUSIVE AND

ARE IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED, EITHER IN FACT OR BY

OPERATION OF LAW, STATUTORY OR OTHERWISE, INCLUDING WARRANTIES OF MERCHANTABILITY

AND FITNESS FOR A PARTICULAR PURPOSE. TRENDWARE NEITHER ASSUMES NOR AUTHORIZES

ANY OTHER PERSON TO ASSUME FOR IT ANY OTHER LIABILITY IN CONNECTION WITH THE SALE,

INSTALLATION MAINTENANCE OR USE OF TRENDWARE’S PRODUCTS.

Содержание TEG-S2400I - DATA SHEETS






















































































































































Результаты поиска

Содержание TEG-S2400I - DATA SHEETS

Отзывы:

TRENDnet TEG-S2400I - DATA SHEETS, Руководство пользователя, Страница: 147 / 149

Результаты поиска

Содержание TEG-S2400I - DATA SHEETS

Отзывы: