TREND T18S/AG115, Оригинальное руководство пользователя

Страница: 14 / 84

EN - T18S/AG115
-14-
• Plug the charger into a standard 230V~50Hz mains
socket outlet, the green LED on the front left hand side
of the charger will illuminate.
• Do not allow the cable to become knotted or kinked.
• Place the battery pack into the charger base. (Note
the battery has raised ribs which allows it to fit into
the charger only one way). Time the charge 32, 48, 54
minutes only.
• The red LED on the front right hand side of the charger
will illuminate to indicate charging is in progress. A
green LED will illuminate when the battery is fully
charged.
• Unplug the charger when not in use and store it in a
suitable storage cabinet.
• Avoid charging your battery in freezing conditions as
charging power will not be sufficient.
• When charging more than one battery pack in
succession allow at least 30 minutes for the charger to
cool down before charging an additional battery.
• Always remove the battery pack and store it safely
when the tool is not in use.
CAUTION:
If at any point during the charging
process none of the LEDs are lit, remove the battery
pack from the charger to avoid damaging the product.
DO NOT insert another battery.
Cooling System
The charger is equipped with an internal fan designed
to cool the charger. Never operate the charger if the
fan does not operate properly or if ventilation slots are
blocked. Do not permit foreign objects to enter the
interior of the charger.
Hot/cold Pack Delay
When the charger detects a battery pack that is too
hot or too cold, it automatically starts a Hot/Cold Pack
Delay, suspending charging until the battery pack has
reached an appropriate temperature. The charger then
automatically switches to the pack charging mode. This
feature ensures maximum battery pack life.
Electronic Protection system
Trend Li-Ion tools are designed with an Electronic
Protection System that will protect the battery pack
against overloading, overheating or deep discharge.
The tool will automatically turn off if the Electronic
Protection System engages.
Battery Charging Indoors
This charger is designed to be used indoors. We do not
recommend that it is used inside your home. Ideally
batteries should be charged on a bench in a workshop,
garage or shed. If the charging operation is to be carried
out in your home the area must be well ventilated and
the charger must be placed on a non combustible
surface ensuring that the ventilation slots are not
blocked
Wall Mounting
These chargers are designed to be wall mountable or to
sit upright on a table or work surface. If wall mounting,
locate the charger within reach of an electrical outlet,
and away from a corner or other obstructions which
may impede air flow. Use the back of the charger as a
template for the location of the mounting screws on the
wall. Mount the charger securely using suitable fixings
depending on wall type, a head diameter of 7 – 9mm
and length of 25mm is recommended. Leave a suitable
length of the screw exposed to allow the charger to be
fitted. Align the slots on the back of the charger with the
exposed screws and fully engage them in the slots.
Charger Cleaning Instructions
WARNING:
Shock hazard. Disconnect the
charger from the AC outlet before cleaning. Dirt and
grease may be removed from the exterior of the charger
using a cloth or soft non-metallic brush. Do not use
water or any cleaning solutions. Never let any liquid get
inside the tool; never immerse any part of the tool into
a liquid.
Battery Packs
Important Safety Instructions for All Battery Packs
When ordering replacement battery packs, be sure to
include product reference and voltage.
The battery pack is not fully charged out of the carton.
Before using the battery pack and charger, read
the safety instructions below. Then follow charging
procedures outlined.
READ ALL INSTRUCTIONS
• Do not charge or use battery in explosive
atmospheres, such as in the presence of
flammable liquids, gases or dust.
Inserting or
removing the battery from the charger may ignite the
dust or fumes.
•
Never force battery pack into charger. Do not
modify battery pack in any way to fit into a non-
compatible charger as battery pack may rupture
causing serious personal injury.
• Charge the battery packs only in Trend chargers.
•
DO NOT splash or immerse in water or other liquids.
• Do not store or use the tool and battery pack
in locations where the temperature may fall
below 4ºC (34ºF) (such as outside sheds or metal
buildings in winter), or reach or exceed 40ºC
(104ºF) (such as outside sheds or metal buildings
in summer).