manualshive.com logo in svg

Travis Industries Xtrordinair ProBuilder 36 CleanFace MV, Руководство пользователя

Поделиться
Скачать
Travis Industries Xtrordinair ProBuilder 36 CleanFace MV Скачать руководство пользователя страница 6

6 

Operation 

© Travis Industries 

5/9/19 - 1490 

PB 36/44 CF MV Operation 

Before You Begin 

  Read this entire manual before you use your new fireplace (especially the section "Safety 

Precautions" on pages 4 & 5).  Failure to follow the instructions may result in property damage, bodily 
injury, or even death. 

Location of Controls 

There is a door on the lower portion of the screen assembly to provide access to the manual controls on 
the fireplace.  The door is held closed by two magnets.  Open the door by gently pulling outward on the 
upper portion of the lower trim. 

 

 

On/Off Switch

 

This control is used to turn the heater on and off. 

Pilot Igniter

 

The pilot igniter is used only to start the pilot.  When pressed, it sends an 
electrical charge to the pilot assembly.  This creates a blue spark directly 
next to the pilot, igniting the pilot flame. 

Gas Control Knob

 

This knob is used to control gas to the heater and for starting the pilot.  There 
are three positions, ON, OFF, & PILOT.  The pointer to the left of the knob 
indicates the position this knob is in. 

Flame Adjust Knob

 

This knob controls the flame height from low ("LO") to high ("HI").  The 
pointer above the knob points to the position this knob is in. 

Optional Remote Receiver

  The receiver is used in conjunction with the optional remote thermostat.  It is 

used to control the remote and replaces the on/off switch for direct operation. 

Optional Blower Dial

 

This dial controls the speed of the internal convection blower that pushes the 
heated air into the room. 

 

Optional Light Dial

 

This dial controls the brightness of the optional accent lights (if applicable). 

 

 

Rotate the Control Door Down to 

Access Controls

Shutoff Valve

(accessible with 

screen removed)

Pilot Igniter

On/Off Switch

Optional Blower Dial

Optional Remote Receiver

Gas Control Knob

Flame Adjust Knob

Optional EmberLight Dial

Содержание Xtrordinair ProBuilder 36 CleanFace MV





































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды