manualshive.com logo in svg

Travis Industries Xtrordinair ProBuilder 36 CleanFace MV, Руководство пользователя

Поделиться
Скачать
Travis Industries Xtrordinair ProBuilder 36 CleanFace MV Скачать руководство пользователя страница 19

 

Maintenance

 

19 

© Travis Industries 

5/9/19 - 1490 

PB 36/44 CF MV Operation 

ProBuilder 42 Log Set Installation 

Installation Warnings 

NOTE

:  Consult the installation manual for order of installation.  If using propane (LP), convert the 

appliance before installing the log set.  If using firebacks, install them prior to installing the log 
set. 

 

The logs are fragile, especially after being exposed to heat.

 

  Make sure the gas control valve is OFF and the heater is cool prior to installing logs. 

  Failure to position the parts in accordance with these diagrams or failure to use only parts 

specifically approved with this appliance may result in property damage or personal injury. 

  The burner must be correctly positioned before installing the log set. Make sure the burner is fully 

seated and the pilot is properly aligned. See owner’s manual for details on burner removal. 

Log Set Overview – MV/GSB2 Models 

When installed, the (8) logs should appear as shown below.  See the following pages for installation. 

Log Name 

Rear Log 

Left Log 

Right Log 

Left Twig 

Right Front 

Twig 

Right Rear 

Twig 

Left Ember 

Chunk 

Right Ember 

Chunk 

Replacement Part 

Number 

250-05070 

250-05071 

250-05072 

250-05073 

250-05074 

250-05075 

250-05076 

250-05077 

Number on Back of 

Log 

1 

2 

3 

4 

5 

6 

7 

8 

 

 

Left Twig 

250-05073 

Right Rear Twig 

250-05075 

Rear Log 

250-05070 

Right Ember Chunk 

250-05077 

Right Log 

250-05072 

Right Front Twig 

250-05074 

Left Ember Chunk 

250-05076 

Left Log 

250-05071 

Содержание Xtrordinair ProBuilder 36 CleanFace MV





































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды