manualshive.com logo in svg

Travis Industries Xtrordinair ProBuilder 36 CleanFace MV, Руководство пользователя

Поделиться
Скачать
Travis Industries Xtrordinair ProBuilder 36 CleanFace MV Скачать руководство пользователя страница 24

24 

Maintenance 

© Travis Industries 

5/9/19 - 1490 

PB 36/44 CF MV Operation 

Ember Chunk Identification 

There are (2) ember chunks, that look very similar, included with this log set.  It is important that they are 
on the correct side of the burner or they may cause flame impingement.  Below is a picture that shows the 
ember chunks side by side to aid with identification. 

 

Left Chunk

 

Right Chunk

 

 

 

 

Left Ember Chunk 

The left ember chunk and has a flat bottom and charred end.  The chunk fits behind the bar, 2

nd

 from the 

left, of the log grate.  The charred end should be to the left.  Place the ember chunk as shown below.  
Make sure the chunk is positioned so it does not cover any burner holes. 
 

  

 

Right Ember Chunk 

The right ember chunk also has a charred end.  The chunk fits behind the bar, 2

nd

 from the right, of the 

log grate.  The charred end should also be to the left as shown below. 
 

  

 

 

 

View from above 

Do not block 
burner holes 

View from above 

Do not block 
burner holes 

Содержание Xtrordinair ProBuilder 36 CleanFace MV





































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды