manualshive.com logo in svg

Travis Industries Xtrordinair ProBuilder 36 CleanFace MV, Руководство пользователя

Поделиться
Скачать
Travis Industries Xtrordinair ProBuilder 36 CleanFace MV Скачать руководство пользователя страница 25

 

Maintenance

 

25 

© Travis Industries 

5/9/19 - 1490 

PB 36/44 CF MV Operation 

Ember bed Glass and Ember Material Installation (GSR2 ONLY)  

Ember bed Glass Installation 

The Ember-Glo™ lights come standard on the GSR2 units.  There are an optional accessory for GSB2 
or MV units.  If the upgrade kit is not used in for the GSB2 or MV units, you may skip this section and 
proceed to Ember Installation. 

  Make sure the ember skirt is in place.  The skirt hooks over the front of the ember platform and 

slopes outward toward the glass.  The skirt helps keep the glass and ember material from 
falling off the platform when the glass is removed. 

  Locate the perforations in front of the log grate.   

 

  Place a thick layer of the ember glass over the perforations making sure to cover all of the 

holes completely. 

 

  Lightly dress the ember glass with the black touch-up paint provided.  Check the appearance 

with the lights on and add additional paint, as needed, for a realistic glowing ember 
appearance.   

 

NOTE:  

If power is supplied to the fireplace it can helpful to turn the lights on while painting so you can 

determine an appropriate amount of paint for a realistic ember appearance. 

 

NOTE: 

 We recommend that you use a piece of paper, cardboard as a shield to mask the log grate 

and burner from overspray (see below). 

Содержание Xtrordinair ProBuilder 36 CleanFace MV





































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды