background image

NOTE 1

At 80 MHz and 800 MHz, the higher frequency range applies.

NOTE 2

These guidelines may not apply in all situations. Electromagnetic

propagation is affected by absorption and reflection from structures, objects and
people.

a  Field strengths from fixed transmitters, such as base stations for radio

(cellular/cordless) telephones and land mobile radios, amateur radio, AM and FM
radio broadcast and TV broadcast cannot be predicted theoretically with accuracy.
To assess the electromagnetic environment due to fixed RF transmitters, an
electromagnetic site survey should be considered. If the measured field strength in
the location in which the ELE007839V1 is used exceeds the applicable RF
compliance level above, the ELE007839V1 should be observed to verify normal
operation. If abnormal performance is observed, additional measures may be
necessary, such as reorienting or relocating the ELE007839V1.

b Over the frequency range 150 kHz to 80 MHz, field strengths should be less than 3 V/m. 

0,01

0,1

7

6

1

.

1

7

6

1

.

1

1

0

9

6

.

3

0

9

6

.

3

0

1

150 kHz to 80 MHz

d = 1.167

80 MHz to 800 MHz

d = 1.167

800 MHz to 2,5 GHz

d = 2.333

Table 6 Recommended separation distances between portable and mobile

RF communications equipment and the EQUIPMENT or SYSTEM –

for ME EQUIPMENT or ME SYSTEM that are not LIFE-SUPPORTING

Recommended separation distances between portable and mobile RF communica-

tions equipment and the ELE007839V1 Fitness Equipment.

The TMB-

1014-BT is intended for use in an electromagnetic environment in which

radiated RF disturbances are controlled. The customer or the user of the TMB-

1014-

BT can help prevent electromagnetic interference by maintaining a minimum distance
between portable and mobile RF communications equipment (transmitters) and the
TMB-

1014-BT as recommended below, according to the maximum output power of the

communications equipment.

Rated maximum output

power of transmitter

W

Separation distance according to frequency of transmitter

m

100

For transmitters rated at a maximum output power not listed above, the recommended
separation distance

d

in meters (m) can be estimated using the equation applicable to

the frequency of the transmitter, where

P

is the maximum output power rating of the

transmitter in watts (W) according to the transmitter manufacturer.
NOTE 1 At 80 MHz and 800 MHz, the separation distance for the higher frequency
range applies.
NOTE 2 These guidelines may not apply in all situations. Electromagnetic propagation
is affected by absorption and reflection from structures, objects and people.

0.167 

  

0.167 

 

0.233

0.369 

  

0.369 

 

0.738

3

3

3

.

2

8

8

3

.

7

11.67 

  

11.67 

 

23.330

Содержание TMB-1014-BT
















Отзывы: