Transition Networks SISGM1040-244 Скачать руководство пользователя

Страница: 88 / 117

Transition Networks

SISGM1040-244

24-Hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600

DMI interface

Port 5 to port 8 support DMI function. The DMI table shows five parameters and four

warning and alarm indicators. All of these warning and alarm were defined and

evaluated by SFP transceiver with DMI function.

And then, click

Apply

to apply the settings

VLAN configuration

A Virtual LAN (VLAN) is a logical network grouping that limits the broadcast domain,

which would allow you to isolate network traffic, so only the members of the VLAN will

receive traffic from the same members of VLAN. Basically, creating a VLAN from a switch

is logically equivalent of reconnecting a group of network devices to another Layer 2

switch. However, all the network devices are still plugged into the same switch physically.

The industrial switch supports port-based and 802.1Q (tagged-based) VLAN. The default

configuration of VLAN operation mode is

Disable

Содержание SISGM1040-244






















































































































Результаты поиска

Содержание SISGM1040-244

Отзывы:

Похожие инструкции для SISGM1040-244

Бренды по названию

Популярные бренды

Transition Networks SISGM1040-244, Руководство пользователя

Результаты поиска

Содержание SISGM1040-244

Отзывы:

Похожие инструкции для SISGM1040-244

Бренды по названию

Популярные бренды