Transition Networks SISGM1040-244 Скачать руководство пользователя страница 108

Страница: 108 / 117

Transition Networks

SISGM1040-244

24-Hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600

IGMP Configuration interface

X-Ring

X-Ring provides a faster redundant recovery than Spanning Tree topology. The action is

similar to STP or RSTP, but the algorithms not the same.

In the X-Ring topology, every switch should enable X-Ring function and assign two

member ports in the ring. Only one switch in the X-Ring group would be set as a master

switch that would be blocked, called backup port, and another port is called working port.

Other switches in the X-Ring group are called working switches

and their two member

ports are called working ports. When the failure of network connection occurs, the backup

port will automatically become a working port to recovery the failure.

The switch supports the function and interface for setting the switch as the ring master or

slave mode. The ring master can negotiate and place command to other switches in the

X-Ring group. If there are 2 or more switches in master mode, then software will select

the switch with lowest MAC address number as the ring master. The X-Ring master ring

mode will be enabled by the X-Ring configuration interface. Also, user can identify the

switch as the ring master from the R.M. LED panel of the LED panel on the switch.

The system also supports the coupling ring that can connect 2 or more X-Ring group for

the redundant backup function and dual homing function that prevent connection lose

between X-Ring group and upper level/core switch.

Enable X-Ring:

To enable the X-Ring function. Marking the check box to enable the

X-Ring function.

Enable Ring Master:

Mark the check box for enabling this machine to be a ring

master.

& 2

Ring Ports:

Pull down

the selection menu to assign two ports as the

member ports.

Ring Port

is the working port and

Ring Port

is the backup port.

When

Ring Port

fails, the system will automatically upgrade the

Ring Port

be the working port.

Enable Coupling Ring:

To enable the coupling ring function. Marking the check box

Содержание SISGM1040-244






















































































































Результаты поиска

Содержание SISGM1040-244

Отзывы:

Похожие инструкции для SISGM1040-244

Бренды по названию

Популярные бренды

Transition Networks SISGM1040-244, Руководство пользователя

Результаты поиска

Содержание SISGM1040-244

Отзывы:

Похожие инструкции для SISGM1040-244

Бренды по названию

Популярные бренды