Transition Networks SISGM1040-244 Скачать руководство пользователя страница 11

Страница: 11 / 117

Transition Networks

SISGM1040-244

24-Hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600

Features

Provides 4 x 10/100/1000Base-T Mbps Ethernet ports

Provides 4 x SFP (mini-GBIC) port (support 100/1000 Dual Mode)

SFP supports DMI function

Supports full/half duplex flow control

Supports auto-negotiation

Supports MDI/MDI-X auto-crossover

Supports Packet Buffer up to 1Mbits

Supports MAC Address up to 8Kbytes

Supports surge (EFT) protection 3,000 V

for power line

Supports 6,000 V

Ethernet ESD protection

Power Supply

Wide-range Redundant Power Design

Power Polarity Reverse Protect

Overload Current Protection

Case/Installation

IP-30 Protection

DIN Rail and Wall Mount Design

Spanning Tree

Support IEEE802.1d Spanning Tree

Support IEEE802.1w Rapid Spanning Tree

VLAN

Port Based VLAN

Support 802.1 Q Tag VLAN

GVRP

X-Ring

X-Ring, Dual Homing and Couple Ring Topology

Provide redundant backup feature and the recovery time below

20ms

Port Trunk with LACP

QoS (Quality of Service)

Support IEEE 802.1p Class of Service

Per port provides 4 priority queues

Port Base, Tag Base and Type of Service Priority

Bandwidth Control

Ingress Packet Filter and Egress Rate Limit

Broadcast/Multicast Packet Filter Control

Содержание SISGM1040-244






















































































































Результаты поиска

Содержание SISGM1040-244

Отзывы:

Transition Networks SISGM1040-244, Руководство пользователя, Страница: 11 / 117

Результаты поиска

Содержание SISGM1040-244

Отзывы: