Transition Networks SISGM1040-244 Скачать руководство пользователя страница 19

Страница: 19 / 117

Transition Networks

SISGM1040-244

24-Hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600

Tighten the wire-clamp screws for preventing the wires from loosing.

Note

The wire gauge for the terminal block should be in the range

between 12~ 20 AWG.

LED Indicators

There are few LEDs display the power status and network status located on the front

panel of 4 10/100/1000T + 4 SFP Industrial Switch, each of them has its own specific

meaning as tabled below.

LED

Color

Description

The industrial switch is the master of the X-ring

group

R-Master

Green

Off

The industrial switch is not the master of the X-ring

group

Power input 1 is active

PWR1

Green

Off

Power input 1 is inactive

Power input 2 is active

PWR2

Green

Off

Power input 2 is inactive

Power input 1 or 2 is inactive or port link down

(depends on Fault Relay Alarm configuration)

P-Fail

Red

Off

Power input 1 and 2 are both functional, or no power

inputs

Содержание SISGM1040-244






















































































































Результаты поиска

Содержание SISGM1040-244

Отзывы:

Transition Networks SISGM1040-244, Руководство пользователя, Страница: 19 / 117

Результаты поиска

Содержание SISGM1040-244

Отзывы: