Transition Networks S4224 Скачать руководство пользователя страница 180 | Manualshive

Страница: 180 / 669

Transition Networks S4224 Скачать руководство пользователя страница 180

Transition Networks

S4224 Web User Guide

33558 Rev. C

https://www.transition.com

Page 180 of 669

requested by the receiver. By so limiting the source, SSM reduces demands on the network and

improves security. SSM requires that the receiver specify the source address and explicitly excludes

the use of the (*,G) join for all multicast groups in

, which is possible only in IPv4's IGMPv3

and IPv6's MLDv2.
SSM can be viewed in contrast to ASM (Any-Source Multicast), where a receiver expresses interest

in traffic to a multicast address. The multicast network must 1) discover all multicast sources sending

to that address, and 2) route data from all sources to all interested receivers. ASM is particularly well

suited to groupware applications where 1) all participants in the group want to be aware of all other

participants, and 2) the list of participants is not known in advance. With ASM, the source discovery

burden on the network can become significant with a large number of sources.
With SSM, the receiver expresses interest in traffic to a multicast address, and also expresses

interest in receiving traffic from just one specific source sending to that multicast address. This keeps

the network from having to discover numerous multicast sources, and reduces the amount of

multicast routing information that the network must maintain. SSM requires support in last-hop routers

and in the receiver's operating system. SSM support is not required in other network components

(including routers and even the sending host). Interest in multicast traffic from a specific source is

conveyed from hosts to routers using IGMPv3 as specified in

. In SSM, some types of

denial of service (DoS) attack cannot be made by simply sending traffic to a multicast group.
SSM destination addresses must be in the ranges 232.0.0.0/8 for IPv4 or FF3x::/96 for IPv6.

See

http://tools.ietf.org/html/rfc4607

for the full set of reserved addresses.

Leave Proxy Enabled

Check to enable IGMP Leave Proxy. This feature can be used to avoid forwarding unnecessary leave

messages to the router side. The default is unchecked.

Proxy Enabled

Check to enable IGMP Proxy. This feature can be used to avoid forwarding unnecessary join and

leave messages to the router side. The default is unchecked.

Port

The S4224 logical port number. The * in the Port column acts as a ‘wild card’ character which causes

the selections in this row to be applied to all other Ports (rows) in the table for which this selection is

valid.

Router Port

Specify which ports act as router ports. A router port is an Ethernet port on the S4224 that leads

towards the Layer 3 multicast device or IGMP querier. If an aggregation member port is selected as a

router port, the whole aggregation will act as a router port. The default is unchecked.

Check to enable the fast leave on the port. With IGMP fast-leave processing enabled, the S4224

immediately removes the interface attached to a receiver on reception of a Leave Group message.

This speeds up leave processing, but should only be used when receivers are directly attached to the

S4224.

The default is unchecked (fast leave disabled on the port).

When you enable IGMP fast-leave processing, the S4224 immediately removes a port when it detects

an IGMP v2 leave message on that port.

Throttling

Select

unlimited

or a value from

1

-

10

to limit the number of multicast groups to which an S4224

port can belong. The default is

unlimited

.

«
...
178
179
180
181
182
...
»

Содержание S4224






























































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов