Trane VAV-UCM 4.2 Скачать руководство пользователя страница 65 | Manualshive

Страница: 65 / 88

background image

VAV-SVX01C-EN

65

Troubleshooting

1.

If the wireless zone sensor system failure

•

Observe LED5 on the receiver. LED5 will be On solid green whenever the receiver is
powered.

•

Make sure the receiver is properly grounded. Both the black wire (GND SIGNAL) and the
yellow wire (GND-POWER) must be grounded.

•

Press the Test button (S5) on the sensor. LED5 should turn On solid green, indicating proper
battery strength. LED1, LED2, and LED3 will indicate signal strength (See table 2).

Table 16. Diagnostics: LED1, LED2, LED3 on the receiver

User Action

LED Display

(a)

(a)

1 Blink pattern is On for ¼ s, Off for ¼ s, with 2 s Off between repetitions.

Indicates…

None

LED1:Off
LED2:Off
LED3:1-blink pattern repeated
continuously

Disassociated
* Receiver is not associated, waiting for a sensor.
* Receiver lost communication with sensor.
* Receiver has no devices on its wireless personal
area network.
* Association with a device has been manually
removed.

None

LED1:Off
LED2:Off
LED3:2-blink pattern repeated
continuously

Address set to 000
* Address not set to between 001-999

None

LED1:Off
LED2:Off
LED3:3-blink pattern repeated
continuously

Not Configured
* Receiver configuration properties not properly set
(defective receiver)

Table 17. Battery status: LED5 on the sensor

User Action

LED Display

Indicates…

Press Test
Button (SS)

Solid green for 5 seconds

Battery condition is adequate for proper operation.

Solid red for 5 seconds

Battery condition is low. Batteries should be replaced.

No light

Batteries are totally dead or not installed properly, or sensor
is defective.

None

Blinking red: 1-blink pattern

1

repeated 5

times. Cycle repeats every 15 minutes.

Battery condition is low. Approximately 14 days of operation
remain before the battery is too weak to power the sensor.

Note:

1 Blink pattern is On for ¼ s, Off for 3/4 s, with 2 s Off between repetitions.

Table 18. Signal quality: LED1, LED2, LED3 on the sensor

User Action

LED Display

Indicates…

None

LED1:Off
LED2:Off
LED3:Off

Normal state
* No Test button press

Press Test
Button (SS)

LED1:Off
LED2:Off
LED3:Off

Associated; no communication with receiver
* Associated, but no signal from the receiver after
pressing Test button

Press Test
Button (SS)

LED1:On
LED2:On
LED3:On
Displays for 5 seconds, then constantly off

Excellence signal quality
* Adequate signal margin for reliable communication.

Press Test
Button (SS)

LED1:Off
LED2:On
LED3:On
Displays for 5 seconds, then constantly off

Marginal signal quality
* Reduced battery life likely.
* Consider moving the sensor or receiver to a better
location.

«
...
63
64
65
66
67
...
»

Содержание VAV-UCM 4.2

























































































Отзывы:

Нет отзывов

Похожие инструкции для VAV-UCM 4.2

Бренд: Jafar Страницы: 9

Бренд: wattio Страницы: 20

Бренд: Sole Diesel Страницы: 8

Бренд: Samson Страницы: 36

Бренд: FBII Страницы: 71

Бренд: CAME Страницы: 4

Бренд: Eaton Страницы: 2

Бренд: Eaton Страницы: 2

PowerXL DX-NET-ETHERCAT-2

Бренд: Eaton Страницы: 3

Бренд: FAAC Страницы: 4

Бренд: FAAC Страницы: 52

Бренд: GARAN Страницы: 8

Бренд: Gamma Vacuum Страницы: 25

Бренд: Gamma Страницы: 28

Бренд: National Instruments Страницы: 14

Бренд: National Instruments Страницы: 11

Бренд: Nauticam Страницы: 2

Бренд: National Instruments Страницы: 18

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды