manualshive.com logo in svg

Trane VAV-UCM 4.2, Инструкция по установке и обслуживанию


Поделиться
Скачать
background image

4

 VAV-SVX01C-EN

Table of Contents

UCM Programming and Operation 

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  30

Chapter Overview 

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  30

Accessing Rover/Comm4 

 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  30

Rover Overview  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  30
Laptop Requirements and Complete Connection Instructions  . . . . . . . .  30

UCM Home Tabs: At a Glance 

 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  33

Status Tab   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  34
Setpoints Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  35
Wireless Tab   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  35
Advanced Configuration Tab  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  35

UCM Home Tabs: Instructions 

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  36

Configuration:   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  36
Setpoints Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  36
Wireless Tab   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  43
Advanced Configuration Tab  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  43

Entering and Exiting the Service Mode 

 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  44

Overriding VAVs 

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  45

Resetting Diagnostics 

 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  45

Downloading Program Files from PC to DDC UCM 4.2  . . . . . . . . . . . . . .  46

Sequence of Operations 

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  48

Chapter Overview 

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  48

Single Duct Units 

 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  48

Override Conditions (Single Duct) 

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  48

Fan-Powered Units 

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  49

Parallel Fan-Powered Units 

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  49

Occupied Units   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  49

Override Conditions (Parallel Fans) 

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  50

Series Fan-Powered Units 

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  51

Occupied Units   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  51

Override Conditions (Series Fan) 

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  51

Zone Sensor Functions 

 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  52

Flow Sensor 

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  53

Failure Modes 

 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  53

Air and Water Balancing 

 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  54

Chapter Overview 

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  54

Air Balancing 

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  54

System Checkout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  54
System Setup   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  54
VAV Single Duct Unit Air Balancing   . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  55

Содержание VAV-UCM 4.2

























































































Отзывы:

Нет отзывов

Похожие инструкции для VAV-UCM 4.2

Waters 2690 Quick Start Manual preview
2690
Бренд: Waters Страницы: 55
Paradox IP150 Programming Manual preview
IP150
Бренд: Paradox Страницы: 2
ZEHUS Controller Rider'S Manual preview
Controller
Бренд: ZEHUS Страницы: 28
Valfonta S3 Operation And Installation Instructions Manual preview
S3
Бренд: Valfonta Страницы: 12
Salda FLEX Service Manual preview
FLEX
Бренд: Salda Страницы: 20
LAE electronic LF28 Instructions For Installation And Use Manual preview
LF28
Бренд: LAE electronic Страницы: 7
LAE electronic AT1-5 Instructions For Use preview
AT1-5
Бренд: LAE electronic Страницы: 2
National Instruments PXIe-4302 Calibration Procedure preview
PXIe-4302
Бренд: National Instruments Страницы: 14
National Instruments PXIe-4302 User Manual preview
PXIe-4302
Бренд: National Instruments Страницы: 31
National Instruments NI-9244 User Manual And Specifications preview
NI-9244
Бренд: National Instruments Страницы: 50
National Instruments NI 9870 Operating Instructions And Specifications preview
NI 9870
Бренд: National Instruments Страницы: 24
National Instruments NI 9247 Getting Started Manual preview
NI 9247
Бренд: National Instruments Страницы: 21
National Instruments NI 9242 Getting Started Manual preview
NI 9242
Бренд: National Instruments Страницы: 39
National Instruments NI 9218 Getting Started preview
NI 9218
Бренд: National Instruments Страницы: 22
National Instruments NI 9263 Calibration Procedure preview
NI 9263
Бренд: National Instruments Страницы: 8
National Instruments NI 9425 Getting Started Manual preview
NI 9425
Бренд: National Instruments Страницы: 20
National Instruments NI 9234 Getting Started preview
NI 9234
Бренд: National Instruments Страницы: 9
National Instruments FIeldPoint FP-AO-200 Operating Instructions Manual preview
FIeldPoint FP-AO-200
Бренд: National Instruments Страницы: 13

Бренды по названию

Популярные бренды

Загрузить еще бренды