manualshive.com logo in svg

Trane BCHC, Руководство по установке и эксплуатации

Поделиться
Скачать
Trane BCHC Скачать руководство пользователя страница 39

BCXC-SVX01A-EN

39

Operation

Sequence of
Operation

Analog Inputs

See Table O-SO-11 on page 40 for a
complete description of analog inputs.

Binary Outputs

Binary outputs are configured to support
the following:
• Two fan stages (when one or two fan

stages are present, J1-2 can be
configured as exhaust fan)

• One hydronic cooling stage
• One hydronic heating stage

(dehumidification requires this to be in
the reheat position)

• One DX cooling stage
• One or two-stage electric heat

(dehumidification requires this to be in
the reheat position)

• Face and bypass damper
• Modulating fresh air damper (Tracer

ZN520 only)

• One-stage baseboard heat

Table O-SO-10. Binary Input Configurations

Binary

Controller Operation

Input

Description

Configuration

Contact closed

Contact open

BI 1

Low temperature

NC

normal

diagnostic

detection (Note 1)

(note 5)

BI 2

Condensate overflow

NC

normal

diagnostic

(Note 1)

(note 5)

BI 3

Occupancy

NO

unnnoccupied

occupied

BI 3

Generic binary input

NO

normal (note 3)

normal (note 3)

BI 4

Fan status (Note 1)

NO

normal

diagnostic

Note 1: During low temperature, condensate overflow, and fan status diagnostics, the Tracer

®

 ZN520 control disables all

normal unit operation of the fan, valves, and damper.

Note 2: The occupancy binary input is for standalone unit controllers as an occupied/unoccupied input. However, when the

controller receives a communicated occupied/unoccupied request, the communicated request has priority over the
hardwired input.

Note 3: The generic binary input does not affect unit operation. A building automation system reads this input as a generic

binary input

Note 4: If the fan mode input is in the off position or the controller is in the unoccupied mode with the fan off, the fan

status input will be open. A diagnostic will not be generated when the controller commands the fan off. A diagnostic
will only be generated if the fan status input does not close after one minute from energizing a fan output or any time
the input is open for one minute. The controller waits up to one minute after energizing a fan output to allow the
differential pressure to build up across the fan.

Note 5: The table below shows the controller’s response to low temperature detection, condensate overflow, and fan

status diagnostics.

BIP

Description

Fan       Valve

Electric heat

Damper

BI 1

Low temperature detection

off

open

off

closed

BI 2

Condensate overflow

off

closed

off

closed

BI 4

Fan status

off

closed

off

closed

Binary Inputs

Tracer ZN controllers have the following
binary inputs, factory-configured for the
following functions:
• Binary input 1: low temperature

detection (freezestat)

• Binary input 2: condensate overflow
• Binary input 3: occupancy/ generic
• Binary input 4: fan status (Tracer ZN520

only)

Note: The generic binary input can be
used with a Tracer Summit

®

 building

automation system only.

BIP1: Low Temperature Detection
Option
The factory hard wires the low
temperature detection sensor to binary
input #1 (BIP1) on the Tracer ZN
controller. The sensor defaults normally
closed (N.C.), and will trip off the unit on a
low temperature diagnostic when
detecting low temperature. In addition,
Tracer ZN controls unit devices as listed
below:
Fan:

Off

Valves:

Open

Electric heat:

Off

Damper:

Closed

Note: See the “Diagnostics” section for
more information.

BIP2: Condensate Overflow Detection
Option
The factory hard wires the condensate
overflow sensor to binary input #2 (BIP2)
on the Tracer

 

ZN controller. The sensor

defaults normally closed (N.C.), and will
trip off the unit on a condensate overflow
diagnostic if condensate reaches the trip
point. In addition, Tracer

 

ZN controls unit

devices as listed below:
Fan:

Off

Valves:

Closed

Electric heat:

Off

BIP3: Occupancy Sensor
Binary input #3 (BIP3) on Tracer

 

ZN is

available for field- wiring an occupancy
sensor, such as a binary switch or a
timeclock, to detect occupancy. The
sensor can be either normally open or
normally closed. Reference Table 6.

BIP4: Fan Status (ZN520 Only)
Binary input #4 (BIP4) on Tracer

 

ZN is

available for sensor, such as a binary
switch or a timeclock, to detect
occupancy. The sensor defaults normally
open but can be configured as either
normally open or closed.

Содержание BCHC









































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды