manualshive.com logo in svg

Trane BCHC, Руководство по установке и эксплуатации

Поделиться
Скачать
Trane BCHC Скачать руководство пользователя страница 23

BCXC-SVX01A-EN

23

Installation
Procedure

Installation

Figure I-IP-2. When inserting the threaded
rod through the unit knockouts, angle it
through the top, careful not to damage unit
coil or insulation.

Figure I-IP-3. Correct placement of washer
or steel plate and nut between threaded
rod and unit. This helps prevent air leakage.

Figure I-IP-1. How to hang the horizontal unit from the ceiling.

Installing the Unit

Follow the procedures below to install the
blower coil unit.

Horizontal Units, Model BCHC
Install horizontal units suspended from
the ceiling with 

3

/

8

” threaded rods that

are field provided. There are two
knockouts in each corner of the unit for
installation of the threaded rods. Ensure
the ceiling opening is large enough for
unit installation and maintenance
requirements.

BCHC Installation Procedure

Materials needed:
• threaded rods, 

3

/

8

”  (4)

• nuts (8)
• flat washers or steel plates (8)
• vibration isolator hangers or turnbuckles

(4)

1. Determine the unit mounting hole

dimensions. Prepare the hanger rod
isolator assemblies, which are field
provided, and install them in the ceiling.
Trane recommends using  threaded
rods to level the unit. Consult the unit
nameplate or the Dimensions and
Weights section in this manual for the
unit weight. See Figure I-IP-1 for proper
horizontal unit installation.

2. Remove motor access panels and

filter access panels.

3. Punch out the eight knockouts in the top

and bottom panels.

4. Guide the threaded rod through the

unit from the top, careful not to damage
insulation or wiring. See Figure I-IP-2.
Insert the threaded rod at an angle to
help prevent internal unit damage.

5. Put a nut and large flat washer or steel

plate on the bottom of the threaded rod.
See Figure IP-I-3.

6. Put a nut and flat washer or steel plate

on the top to prevent air leakage.

7. Thread the top of the rod into the

isolator or turnbuckle.

8. Hoist the unit to the suspension rods

and attach with washers and lock–nuts.
See Figure I-IP-1 for details.

9. Level the unit for proper coil drainage

and condensate removal from the drain
pan. Refer to the condensate drain trap
instructions on page 20.

10. Connect the ductwork to the unit.

Refer to the Duct Connection section on
page 20.

Содержание BCHC









































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды