Toyota Solara guide Скачать руководство пользователя страница 81 | Manualshive

Страница: 81 / 497

background image

’06 Solara_U (L/O 0502)

80

2006 SOLARA from Feb. ’05 Prod. (OM33667U)

This warning light system monitors the
airbag sensor assembly, front airbag sen-
sors, side and curtain shield airbag sen-
sors, curtain shield airbag sensors, driv-
er’s seat position sensor, driver’s seat belt
buckle switch, front passenger occupant
classification system and indicator light,
front passenger’s seat belt buckle switch,
seat belt pretensioner assemblies, infla-
tors, warning light, interconnecting wiring
and power sources. (For details, see “Ser-
vice reminder indicators and warning buzz-
ers” on page 131 in Section 1- 6.)

If any of the following conditions occurs,
this indicates a malfunction of the airbags
or seat belt pretensioners. Contact your
Toyota dealer as soon as possible.

When the ignition key is turned to the
“ON” position, the light does not come
on or remains on for more than 6 sec-
onds.

The light comes on or flashes while
driving.

The SRS warning light will come on and
front passenger occupant classification in-
dicator light will indicate “OFF” if there is
a malfunction in the front passenger occu-
pant classification system.

In the following cases, contact your Toyota
dealer as soon as possible:

Any of the SRS side airbags and cur-
tain shield airbags have been inflated.

The portion of the doors (shaded in the
illustration) was involved in an accident
that was not severe enough to cause
the SRS side airbags and curtain
shield airbags to inflate.

The surface of the seats with the SRS
side airbag (shaded in the illustration)
is scratched, cracked, or otherwise
damaged.

The portion of the front pillars, rear
pillars or roof side rail garnishes (pad-
ding) containing the curtain shield air-
bags inside (shaded in the illustration)
is scratched, cracked, or otherwise
damaged.

NOTICE

Do not disconnect the battery cables
before contacting your Toyota dealer.

carownersmanual.net

carownersmanual.net

«
...
79
80
81
82
83
...
»

Содержание Solara guide


















































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Solara guide

Electronic Parking Disc II

Бренд: Jacob Jensen Страницы: 28

Бренд: Warrior Products Страницы: 4

Бренд: PullRite Страницы: 10

Бренд: Acura Страницы: 2

Green Motion DC 66

Бренд: Eaton Страницы: 18

Бренд: WABCO Страницы: 52

Бренд: GYS Страницы: 32

Бренд: Lock'er Down Страницы: 2

Бренд: JBA Страницы: 5

Бренд: Goobay Страницы: 2

Бренд: VP Autoparts Страницы: 2

Auto Security AA-9103N

Бренд: Audiovox Страницы: 1

Бренд: Kia Страницы: 673

Бренд: Vauxhall Страницы: 215

2013 Cadillac CTS-V

Бренд: Cadillac Страницы: 6

Бренд: AEM Страницы: 5

DT-Mobil Easy 200 L

Бренд: CEMO Страницы: 80

2014 Accord Coupe EX

Бренд: Honda Страницы: 18

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды