Toyota Solara guide Скачать руководство пользователя страница 69 | Manualshive

Страница: 69 / 497

background image

’06 Solara_U (L/O 0502)

68

2006 SOLARA from Feb. ’05 Prod. (OM33667U)

The SRS side airbag on the passenger
seat will not activate if there is no pas-
senger sitting in the front passenger seat.
However, the side airbag on the passen-
ger seat may deploy if luggage is put in
the seat, or the seat belt is buckled up
regardless of the presence of the occu-
pant in the seat. (As for the front passen-
ger occupant classification system, see
“—Front passenger occupant classification
system” on page 81 in this Section.)

Always wear your seat belt properly.

CAUTION

The SRS side airbag system is de-
signed only as a supplement to the
primary protection of the driver and
front passenger seat belt systems.
To ensure maximum protection in
an accident, the driver and all pas-
sengers in the vehicle must wear
their seat belts properly. Wearing a
seat belt properly during an acci-
dent reduces the chances of death
or serious injury or being thrown
out of the vehicle. For instructions
and precautions concerning the seat
belt system, see “Seat belts” on
page 52 in this Section.

Improperly seated and/or restrained
infants and children can be killed
or seriously injured by the deploy-
ing airbags. An infant or child who
is too small to use a seat belt
should be properly secured using a
child restraint system. Toyota
strongly recommends that all in-
fants and children be placed in the
rear seats of the vehicle and prop-
erly restrained. The rear seats are
the safest for infants and children.
For instructions concerning the
installation of a child restraint sys-
tem, see “Child restraint” on page
85 in this Section.

Do not allow anyone to lean his/her
head or any part of his/her body
against the front door or the area
of the seat from which the SRS
side airbag deploys even if he/she
is a child seated in the child re-
straint system. It is dangerous if
the SRS side airbag inflates, and
the impact of the deploying airbag
could cause death or serious injury
to the occupant.

carownersmanual.net

carownersmanual.net

«
...
67
68
69
70
71
...
»

Содержание Solara guide


















































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Solara guide

Бренд: Camcar Страницы: 2

Бренд: cam Страницы: 2

Бренд: Dapper Lighting Страницы: 2

Бренд: VEAP SHIELD UNITED Страницы: 3

Бренд: Würth Страницы: 36

BASIC TLL171231

Бренд: Tellur Страницы: 5

Бренд: Quadratec Страницы: 6

Бренд: Cadillac Страницы: 352

Бренд: Air Lift Страницы: 28

Бренд: Dolphin Страницы: 16

Бренд: Cadillac Страницы: 20

Бренд: Pyle Страницы: 8

Бренд: Mitsubishi Страницы: 367

Бренд: HAKR Страницы: 2

Prime Design AAL-8003

Бренд: Safe Fleet Страницы: 8

RideControl 59540

Бренд: Air Lift Страницы: 10

Бренд: GMC Страницы: 312

2009 Highlander

Бренд: Toyota Страницы: 19

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды