Toyota Solara guide Скачать руководство пользователя страница 104 | Manualshive

Страница: 104 / 497

background image

’06 Solara_U (L/O 0502)

103

2006 SOLARA from Feb. ’05 Prod. (OM33667U)

CHILD RESTRAINT SYSTEM
INSTALLATION

1. Widen the gap between the seat

cushion and seatback slightly and
confirm the position of the lower an-
chorages near the button on the
seatback.

2. Type A—Latch the hooks of lower

straps onto the anchorages and
tighten the lower straps.

Type B—Latch the buckles onto the
anchorages.

For owners in Canada—The symbol on
a child restraint system indicates the pres-
ence of a lower connector system.

If your child restraint system has a top
strap, it should be anchored. (For the
installation of the top strap, see “—Using
a top strap” on page 98 in this Section.)

For installation details, refer to the instruc-
tion manual equipped with each product.

CAUTION

When using the lower anchorages
for the child restraint system, be
sure that there are no irregular ob-
jects around the anchorages or that
the seat belt is not caught.

Push and pull the child restraint
system in different directions to be
sure it is secure. Follow all the
installation instructions provided by
its manufacturer.

Do not install a child restraint sys-
tem on the rear seat if it interferes
with the lock mechanism of the
front seats. Otherwise, the child or
front seat occupant(s) may be killed
or seriously injured in case of sud-
den braking or a collision.

Lower anchorages for the child restraint
systems complying with the FMVSS225
or CMVSS210.2 specifications are
installed in the rear seat.

The anchorages are installed in the gap
between the seat cushion and seatback of
both rear seats.

Child restraint systems complying with the
FMVSS213 or CMVSS213 specification
can be fixed to these anchorages. In this
case, it is not necessary to fix the child
restraint system with a seat belt on the
vehicle.

—Installation with child
restraint lower anchorages
(convertible)

carownersmanual.net

carownersmanual.net

«
...
102
103
104
105
106
...
»

Содержание Solara guide


















































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Solara guide

Бренд: N-Com Страницы: 28

Бренд: Safe Fleet Страницы: 38

Green Motion DC 66

Бренд: Eaton Страницы: 18

Бренд: Toro Страницы: 24

Бренд: Improved Racing Страницы: 17

Бренд: Broadfeet Страницы: 2

S90 - ACCESSORY PANEL

Бренд: Volvo Страницы: 166

Бренд: Buick Страницы: 371

Бренд: Brodit Страницы: 2

Бренд: Belkin Страницы: 30

Бренд: Mitsubishi Страницы: 141

Бренд: Menabo Страницы: 8

Бренд: Seat Страницы: 372

Бренд: OCAM Страницы: 4

Бренд: Comelit Страницы: 20

Бренд: Ford Страницы: 722

2012 ACCORD COUPE

Бренд: Honda Страницы: 454

Roll-Top Xtreme

Бренд: Truckman Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды