Toyota Solara guide Скачать руководство пользователя страница 133

Страница: 133 / 497

’06 Solara_U (L/O 0502)

132

2006 SOLARA from Feb. ’05 Prod. (OM33667U)

If the indicator or buzzer comes on...

Do this.

(h)

Take vehicle to Toyota dealer. If brake system warning light is also on, stop
immediately and contact Toyota dealer.

(i)

Close all doors.

(j)

Take vehicle to Toyota dealer immediately.

(k)

Adjust tire inflation pressure and turn off warning light by pushing reset switch for a
few seconds. If warning light remains, contact Toyota dealer.

(l)

Add washer fluid.

(m)

Take vehicle to Toyota dealer.

(n)

Replace engine oil.

(o)

Key reminder buzzer

Remove key.

carownersmanual.net

Содержание Solara guide


















































































































































































































































































































































































































































































































Результаты поиска

Содержание Solara guide

Отзывы:

Похожие инструкции для Solara guide

Бренды по названию

Популярные бренды

Toyota Solara guide, Руководство пользователя

Результаты поиска

Содержание Solara guide

Отзывы:

Похожие инструкции для Solara guide

Бренды по названию

Популярные бренды