manualshive.com logo in svg

Toyota Solara guide, Руководство пользователя


Поделиться
Скачать
background image

’06 Solara_U (L/O 0502)

31

2006 SOLARA from Feb. ’05 Prod. (OM33667U)

The system will automatically be set after
30 seconds. When the system is set, the
indicator light will start flashing again.

4. After making sure the indicator light

starts flashing, you may leave the ve-
hicle.

Never leave anyone in the vehicle when
you set the system, because unlocking
from the inside will activate the system.

CANCELLING THE SYSTEM

The system will be cancelled by  the fol-
lowing ways.

Any of the doors are unlocked with the
key or wireless remote control.

The trunk is opened with the wireless
remote control transmitter.

Turn the ignition key to the “ON” posi-
tion.

If the tail lights come on for 2 seconds,
the theft deterrent system has been
alarmed. Check to see if there is any
abnormality with your vehicle.

WHEN THE SYSTEM IS SET

Activating the system

The system will sound the alarm under
the following conditions:

If any of the doors are forcibly un-
locked or opened, or if the trunk or
hood is forcibly opened without the key
or wireless remote control transmitter

If the battery terminal is disconnected
and then reconnected

If the ignition is hotwired

The indicator light will come on when the
system is activated.

If any of the door is unlocked without the
key or wireless remote control transmitter
and the key is not in the ignition switch,
all the doors will be automatically locked
again.

After one minute, the alarm will automati-
cally stop and the indicator light will starts
flashing again.

Reactivating the alarm

Once set, the system automatically resets
the alarm after the alarm stops.

The alarm will activate again under the
same circumstances described in
“Activating the system”.

Stopping the alarm

The alarm will be stopped by the following
three ways:

Turn the ignition key from the “LOCK”
to “ON” position.

Unlock any of the doors with the key
or wireless remote control transmitter.

Open the trunk with the wireless re-
mote control transmitter.

These ways cancel the system at the
same time.

If the battery becomes discharged due
to the vehicle being unused for a long
time, etc., when the battery is recharged
or replaced, the system will give the
alarm. If this happens, immediately unlock
any of the doors with the key or the wire-
less remote control transmitter, and the
alarm will stop.

carownersmanual.net

carownersmanual.net

Содержание Solara guide


















































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Solara guide

K&M 8494 Installation Manual preview
8494
Бренд: K&M Страницы: 3
Whispbar K783W Fitting Instructions Manual preview
K783W
Бренд: Whispbar Страницы: 16
BendPak Autostacker PL-6SR Installation And Operation Manual preview
Autostacker PL-6SR
Бренд: BendPak Страницы: 104
EZTRUNK PHANTOM JK Assembly Manual preview
PHANTOM JK
Бренд: EZTRUNK Страницы: 3
walser 30968 User Instructions preview
30968
Бренд: walser Страницы: 24
Chevrolet 2014 TRAX Owner'S Manual preview
2014 TRAX
Бренд: Chevrolet Страницы: 412
Ecco 5545A Installation And Operating Instructions Manual preview
5545A
Бренд: Ecco Страницы: 12
VER-MAC PCMS Series Operation, Safety And Maintenance Manual preview
PCMS Series
Бренд: VER-MAC Страницы: 64
Jaeger 12020523 Fitting Instructions Manual preview
12020523
Бренд: Jaeger Страницы: 11
Rigid Hitch BULL BAR Installation Instructions preview
BULL BAR
Бренд: Rigid Hitch Страницы: 2
CSL 41802 User Manual preview
41802
Бренд: CSL Страницы: 8
Kuda 191090 Installation Instruction preview
191090
Бренд: Kuda Страницы: 3
Rhino-Rack S400-FK2 Instructions preview
S400-FK2
Бренд: Rhino-Rack Страницы: 2
Gacell SLH 27C User Manual preview
SLH 27C
Бренд: Gacell Страницы: 25
Federal Signal Corporation HighLighter Installation And Programming preview
HighLighter
Бренд: Federal Signal Corporation Страницы: 20
Curt Manufacturing 58987 Installation Manual preview
58987
Бренд: Curt Manufacturing Страницы: 4
Yakima K682 Instructions Manual preview
K682
Бренд: Yakima Страницы: 10
Chevrolet 2001 Cavalier Owner'S Manual preview
2001 Cavalier
Бренд: Chevrolet Страницы: 357

Бренды по названию

Популярные бренды

Загрузить еще бренды