Town & Country Fireplaces TC36.CARE3 Скачать руководство пользователя | Manualshive

Страница: 6 / 48

background image

LATCH HANDLE

Fig. #4

Fig. #5

Fig. #5a

The Town & Country Fireplace installation and venting must conform to the current
CAN/CGA-B149 installation code (in Canada) or the current National Fuel Gas Code,
ANSI Z223.1 (in the USA), and approved per local codes. Only qualified (licensed or
trained) personnel should install this product.

In the state of Massachusetts, only a licensed Plumber and Gas Fitter may install
this product.

In some jurisdictions, the Town & Country Fireplace may be installed in Manufactured Homes
after the "first sale".

Consult local codes for approval. The fireplace must be fastened

in place.

Install in accordance with the current standard Mobile Homes, CAN/CSA Z240 MH (in
CANADA), and the Manufacturer's Home Construction and Safety Standard, Title 24 CFR,
Part 3280 or the current Standard for Fire Safety Criteria for Manufactured Home Installa-
tions, Sites and Communities ANSI/NFPA 501A (in the USA).

Warning: Turn off the fireplace, and allow ample time for the unit to cool before
proceeding.

Caution: The ceramic glass is very fragile, and should be handled with care.

The window frame is held in place by two spring-loaded latches that are operated by a
one-piece latch handle.

1. Remove the TC Finishing Touch Trim Kit from the window frame. (If installed)

2. Using a screwdriver or other similar object, push against the notch in the top of the

latch and grab the bottom of the latch handle as it protrudes. Lift handle until latch hook
disengages. Repeat for other side while holding glass so it does not tip out.

3. Tilt the top of the window frame out to clear the top edge of the unit. Grasp the sides of

the frame and lift up and out to disengage from its bottom track.

4. Place the window frame in a safe place to avoid damage.

5. Re-assemble in reverse order. Latch handle should snap into place and be flush with

window frame when engaged correctly.

6. Reinstall Trim Kit if required.

TIP:

To ensure glass is properly latched, grasp the top left and

right sides of the glass frame, under moderate pressure it

should pull forward and return to original position evenly on

both sides.

6

TC36.CE3 250313-48

Installation Requirements

Manufactured (Mobile) Home

Window Frame Removal

«
...
4
5
6
7
8
...
»

Содержание TC36.CARE3

















































Отзывы:

Нет отзывов

Похожие инструкции для TC36.CARE3

PORTRAIT 530INI

Бренд: Valor Страницы: 46

Бренд: Landmann Страницы: 4

Бренд: Majestic fireplaces Страницы: 28

Gemini33xxx SERIES

Бренд: Astria Страницы: 82

Davos A High FP-DAV0A-10L

Бренд: Nordpeis Страницы: 60

Бренд: Majestic fireplaces Страницы: 24

Бренд: BCP Страницы: 16

Бренд: Blue Rhino Страницы: 8

Бренд: Heatilator Страницы: 24

Бренд: Majestic Страницы: 36

Бренд: United States Stove Страницы: 79

Бренд: Heat & Glo Страницы: 46

Бренд: Laminvale Страницы: 9

Бренд: Flagstone Страницы: 2

Бренд: Royal Страницы: 36

Бренд: Flamelux Страницы: 30

Contura C856W Style

Бренд: Nibe Страницы: 20

Бренд: Horizon Fitness Страницы: 21

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды