Town & Country Fireplaces TC36.CARE3 Скачать руководство пользователя | Manualshive

Страница: 16 / 48

background image

The gas control system is located on the right hand side of the firebox behind an access
panel and the decorative firebox panel (if installed). The fireplace is operated via a wall
control and a hand held remote control unit.

The wall control is connected to the fireplace by a 25 ft. communication cable supplied with the
fireplace. The communication cable can be extended with an optional 25 ft. extension kit.

Installation

1. Place the fireplace in the desired location.

2. Remove the window from the fireplace.

3. Remove access panel from right hand side of the firebox (Fig #25)

4. Connect a 110 V. AC electrical supply to the outlet installed inside the control box

(Fig #26). The fireplace operates on a low voltage supplied by an AC adaptor rated at
110 volts, 60Hz, 0.25A. The optional power vent kit is rated at 115 volts, 60Hz, 1.8A.

The electrical wires can be accessed from both inside and

outside the control box by removing one of the two small

access panels (Fig #27)

The wires from inside the outlet box are connected to

the 110 V.AC supply (Fig.#28)

5. Connect the gas supply to the valve (Fig #26)

6. Plug the A/C adaptor into the outlet (Fig #26)

7. Attach the electrical box for the supplied wall control to the framing in the desired

location (up to 50 ft. away). (25 ft is supplied with fireplace. An additional 25 ft can

be achieved by using the optional kit (Part # 5005.064) available from your

distributor).

OUTLET

ADAPTOR

Fig. #28

Fig. #27

Fig. #26

GAS CONNECTION

ACCESS PANEL

Fig. #25

16

TC36.CE3 250313-48

Maestro Control
Plumbing and Electrical

«
...
14
15
16
17
18
...
»

Содержание TC36.CARE3

















































Отзывы:

Нет отзывов

Похожие инструкции для TC36.CARE3

Бренд: Quadra-Fire Страницы: 28

Бренд: Valor Страницы: 5

Бренд: Duraflame Страницы: 8

Бренд: Valor Страницы: 6

Бренд: Living Страницы: 14

Бренд: Majestic Страницы: 16

SCANDIC DELUXE SDC20RC

Бренд: Dimplex Страницы: 4

Бренд: Valor Страницы: 42

Бренд: Sierra Flame Страницы: 44

Бренд: Somogyi Elektronic Страницы: 20

Бренд: Charlton & Jenrick Страницы: 16

Winchester WIN28E

Бренд: Dimplex Страницы: 4

Бренд: Dimplex Страницы: 77

Бренд: DEKO LIVING Страницы: 9

Бренд: Nibe Страницы: 20

Бренд: Desa Страницы: 44

Бренд: White Mountain Hearth Страницы: 12

ECOFIRE ALLEGRO

Бренд: Palazzetti Страницы: 64

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды