Town & Country Fireplaces TC36.CARE3 Скачать руководство пользователя | Manualshive

Страница: 30 / 48

background image

The lower rear panel is held tight against the
side panels by two "V" brackets located on
the firebox rear wall. Although the brackets
are adjusted at the factory for the best fit,
some adjustment may be necessary. Adjust
the angle of the bracket by hand to ensure
a snug fit.

A Firebox Panel Set must be installed for safe operation. Do not use the fireplace without
panels. Unpack and inspect all panels. The panels need to be installed before the logs are
in place.
Caution: The Firebox Panels are very fragile, and should be handled with care.

1. Remove the Side Panel Retainer located on the underside of the firebox heat shield.

The retainer slips between the lip of the firebox and the heat shield and is retained in
place by two screws (Fig. 51 & Fig. 52).

2. Install the Lower Rear Panel.

PARK AVE. BEIGE HERRINGBONE .............................................. TCPN.36PAC(TC36)
.........................................................................................TCPN.36ARPAC(TC36 ARCH)
MOUNT VERNON RED HERRINGBONE .......................................TCPN.36VRC(TC36)
.........................................................................................TCPN.36ARVRC(TC36 ARCH)
MANHATTAN BEIGE STACKED BRICK ....................................... TCPN.36MNC(TC36)
........................................................................................TCPN.36ARMNC(TC36 ARCH)
BLACK PORCELAIN .................................................................. TCPN.

757031.C(TC36)

............................................................................................TCPN.75702.C(TC36 ARCH)

COFFEE BEAN BROWN PORCELAIN ................................TCPN

.757031CB.C(TC36)

...................................................................................... TCPN.75702CB.C(TC36 ARCH)

(See Porcelain panel instruction manual for specific instructions for these panels) Before
proceeding see burner instructions.

TC36 & TC36 ARCH

PANELS

SIDE PANEL RETAINER

HEAT SHIELD

FIREBOX LIP

Fig. #51

SCREWS

Fig. #52

REAR LOWER PANEL

ADJUSTABLE “V” BRACKET

30

TC36.CE3 250313-48

Firebox Panels Installation

Fig. #50

«
...
28
29
30
31
32
...
»

Содержание TC36.CARE3

















































Отзывы:

Нет отзывов

Похожие инструкции для TC36.CARE3

Oakville Series

Бренд: Napoleon Страницы: 72

Бренд: Napoleon Страницы: 4

Бренд: Valor Страницы: 12

Бренд: Napoleon Страницы: 48

Бренд: Napoleon Страницы: 4

Бренд: Napoleon Страницы: 20

Allure Vertical Series

Бренд: Napoleon Страницы: 120

LUNA 850 V Gold Gas

Бренд: M Design Страницы: 39

JEFFERSON FIRE SURROUND

Бренд: Next Страницы: 11

Бренд: Saey Страницы: 44

Бренд: PSF Страницы: 2

Бренд: Safavieh Furniture Страницы: 3

Бренд: Desa Страницы: 40

Бренд: Heat & Glo Страницы: 33

Бренд: Style selections Страницы: 24

Riverview RDV4136

Бренд: Majestic fireplaces Страницы: 2

Бренд: Vanguard Страницы: 40

Бренд: barbas Страницы: 100

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды