Town & Country Fireplaces TC36.CARE3 Скачать руководство пользователя | Manualshive

Страница: 1 / 48

background image

SERIAL #

TC36.CE3 & TC36.CARE3
INSTALLATION AND
OPERATING INSTRUCTIONS

250313-48 TC36.CE3 &TC36.CARE2 5056.427CE

MODEL:
TC36 & TC36AR
SERIES C
MODULAR DIRECT VENT
FIREPLACE

WARNING:    If  the  information  in  these
instructions  is  not  followed  exactly,  a  fire
or  explosion  may  result  causing  property
damage, personal injury or death.

This appliance may be installed in an aftermarket
permanently located, manufactured home (USA
only) or mobile home, where not prohibited by
local codes.

This appliance is only for use with the type of gas
indicated on the rating plate. This appliance is
not convertible for use with other gases, unless
a certified kit is used.

This appliance is suitable for installation in a
bedroom or bed sitting room.

FOR YOUR SAFETY

Do not store or use gasoline or other
flammable vapors and liquids in the vicinity
of this or any other appliance.

WHAT TO DO IF YOU SMELL GAS

r %POPUUSZUPMJHIUBOZBQQMJBODF
r %POPUUPVDIBOZFMFDUSJDBMTXJUDI
r%POPUVTFBOZQIPOFJOZPVSCVJMEJOH
r *NNFEJBUFMZDBMMZPVSHBTTVQQMJFSGSPN

a neighbour’s phone. Follow the gas
supplier’s instructions.

r *GZPVDBOOPUSFBDIZPVSHBTTVQQMJFSDBMM

the fire department.

Installation and service must be performed by
a qualified installer, service agency or the gas
supplier.

INSTALLER:
Leave this manual with the appliance.
CONSUMER:
Retain this manual for future reference.

1
2
3
...
»

Содержание TC36.CARE3

















































Отзывы:

Нет отзывов

Похожие инструкции для TC36.CARE3

Бренд: Napoleon Страницы: 4

Бренд: PSF Страницы: 2

Бренд: United States Stove Company Страницы: 20

Garden Lights 26371

Бренд: Landmann Страницы: 4

Бренд: Continental Fireplaces Страницы: 148

Бренд: Bronpi Страницы: 81

Бренд: Vanguard Страницы: 12

Brooks 15PFP-BROO24-CHDRY

Бренд: OVE Страницы: 4

Surefire FCC 16

Бренд: Burley Страницы: 32

Бренд: Room&Board Страницы: 32

Prescott White Mantel

Бренд: Early Settler Страницы: 4

ELECTRIFLAME XD Mk2 B-1005344

Бренд: Celsi Страницы: 12

Бренд: EINHELL Страницы: 84

Бренд: Napoleon Страницы: 124

CASUAL FIRESIDE Santorini 51-02

Бренд: O.W. Lee Страницы: 10

Бренд: HWAM Страницы: 20

Бренд: Bluegrass Living Страницы: 8

Emerson GAD15412SP

Бренд: Endless Summer Страницы: 22

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды