manualshive.com logo in svg

Tower Hobbies Tower Trainer 40 ARF, Руководство по сборке

Поделиться
Скачать
Tower Hobbies Tower Trainer 40 ARF Скачать руководство пользователя страница 3

3

❍

4-Channel Radio With 4 Servos

❍

Engine; 

(See Engine Selection)

❍

Spare Glow Plugs (Tower R/C Long – TOWG1001)

❍

Medium Fuel Tubing (GPMQ4131, 3’)

❍

1/4” Latex Foam Rubber Padding (HCAQ1000)

❍

1/16” Foam Wing Seating Tape (GPMQ4422)

❍

#64 Rubber Bands (TOWQ1220)

❍

Screw-Lock Pushrod Connectors (GPMQ3870)

❍

Silicone Sealer

A quality brand .40-size engine will be needed. Also a prop will be
required for the engine (follow the manufacturer’s recommendations
for appropriate sizes). We recommend the Top Flite

®

Power Point

®

brand of props. 

We recommend the following engines:

Tower Hobbies .40 ABC

O.S.

®

.40 LA

TOWG0040

OSMG0040

O.S. .40 FX

SuperTigre

®

GS-40

OSMG0540

SUPG0122

Replacement parts are available from Tower Hobbies for your Tower
Trainer 40. Our order assistance representatives are ready to answer
your questions or to place your order. Call us at (800) 637-6050.

We are so confident that the Tower Trainer 40 ARF is the best almost-
ready-to-fly trainer available that we make this guarantee. You will
successfully learn how to fly with the Tower Trainer or we will replace it
with your choice of another trainer of up to equal value. All we ask is that
you learn under the supervision of a qualified, club-designated instructor,
follow normal safety precautions, fly at an AMA-chartered club field and
construct the kit as outlined in this instruction manual.

If for some reason, you find the design and/or workmanship of the
Tower Trainer is not conducive to learning to fly under the conditions
outlined above, contact Hobby Services at 1-217-398-0007 Monday
through Friday 9am-5pm central time. Or send the Tower Trainer to
Hobby Services, 1610 Interstate Drive, Champaign, Illinois 61822.
The information Hobby Services will need is: a letter explaining what
happened, (the letter is to be signed by the instructor and yourself),
name of flying field, name of instructor, and a copy of invoice as
proof of purchase.

This guarantee is effective for 60 days after you receive the kit and
does not cover incidental items (engines, radio equipment and
hardware, etc.). The kit, along with the above specifications must be
sent to Hobby Services for inspection no later than 60 days after
receipt of the kit. Hobby Services reserves the right to verify all
information provided. Replacement trainer kit options are limited to
flat-bottom wing trainer models and makes available from Tower
Hobbies and one replacement per customer.

The Tower Trainer 40 ARF is a great trainer and we are pleased to make
this unprecedented guarantee. If you have any further questions, feel
free to contact Tower Hobbies at 1-800-637-6050.

TOWER TRAINER GUARANTEE

Replacement Parts
Wing Set – TOWA1111 (Includes wing halves, wing joiner and
servo mounting tray)

Fuselage Set – TOWA1112 (Includes fuselage, engine mount, fuel
tank, pushrods and servo tray)

Fin Set – TOWA1113 (Includes horizontal and vertical stabilizers)

Landing Gear Set – TOWA1114 (Includes nosegear wire, main
gear wire, wheels, wheel collars, mounting hardware)

ORDERING REPLACEMENT PARTS

ENGINE SELECTION

ACCESSORIES REQUIRED TO COMPLETE

YOUR TOWER TRAINER 40

0"

1"

2"

3"

4"

5"

6"

7"

0

10

20

30

40

50

60

70

80

90

100 110 120 130 140 150 160 170 180

Inch Scale

Metric Scale

Содержание Tower Trainer 40 ARF

























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды