background image

Distributed by: D.K.Gas Appliances. PO Box 34191 Erasmia 0023  

website: 

    email: [email protected]

www.totai.co.za

Issue 1-2015

F. Technical specifications  

 

Name 

TOTAI 

Model 

16/DK1023A

Heat Output 

11.0 KW  

Gas Types 

LPG 

Injector Size 

Ø 1.70mm x 1  

Operating Pressure 

2.8 kPa 

Gas Consumption (at Max ) 

800 g/h 

 

NOTE:  

 

TAMPERING:  

FOR OUTDOOR USE ONLY. 

 

Specifications are subject to change without prior notice. 

 

 

G. Troubleshooting 

 

PROBLEM  

PROBABLE CAUSE 

 

SOLUTION 

 

Gas valve may be OFF 

 

Turn the gas valve ON 

 

LPG cylinder empty 

 

Refill LPG cylinder

 

Orifice blocked 

 

Clean or replace Orifice

 

Air in supply system 

 

Purge air from lines  

Pilot will not light

 

Loose connection  

Check all fittings  

Debris around pilot  

Clean dirty area  

Loose connection 

 

Tighten connection 

Thermocouple bad  

Replace Thermocouple  

Gas leak in line  

Check connections 

 

Pilot will not stay on 

 

Lack of gas pressure  

LPG cylinder is near empty 

 

Gas pressure is low 

 

LPG cylinder is near empty 

 

Orifice blocked 

 

Remove, clean and replace 

 

Control knob not ON 

 

Turn knob to ON 

Thermocouple bad 

 

Replace Thermocouple 

 

Burner will not light 

 

Pilot light assembly bent  
or not in correct location 

Place pilot light in correct Position  
and retry 

 

Any repairs to the patio heater must be carried out by a qualified person

Under no circumstances are you allowed to tamper with the jet sizes or modify anything on 
the appliance. Not only is it dangerous , it will also nullify your warranty

GAS-PRESSURE REGULATOR—This appliance is designed to operate on a gas pressure 
of 2,8 kPa. A suitable regulator that complies with the requirements of SANS 1237 must be 
used with this appliance

Hose to be in compliance with SANS 1156-2 or BS 3212. Regulator and hose supplied

12

Содержание 16/DK1023A













Отзывы: