background image

 

PRECAUTIONS

 

 
 

APPLIANCE STAND AND LOCATION 

 

BURN-BACK (FIRE IN BURNER TUBE OR CHAMBER)

 

In the event of a burn-back, where the flame burns back to the jet, 

 immediately turn off the gas supply at the control valve on the panel.  

After ensuring the flame is extinguished, re-light the appliance in the 
normal manner. Should the appliance again burn back, close the  

control valve and call a service technician. Do not use the appliance  

again until the service technician has declared that it is safe to do so. 

 

 

 
 

 

Installation and services should only be a done qualified person.
Do not use the heater in an explosive atmosphere. 
Before use, check the hose. 
Disconnect LPG cylinder before moving the heater.
Do not attempt to alter any parts of the heater. 
Example: Using the heater without reflector or protection guard.
The appliance shall not be used in basements or below ground level.
It must always be placed on a solid and level surface.
Never replace or substitute the regulator use only that one is suitable both appliance category and normal gas 
pressure
The LPG gas cylinder valve should be turned off when the heater is not in use.
Don't not use the heater when it is raining, and do not let any liquid splash to the glass tube when the heater is 
Do not paint protection guard, control box or reflector.
Keep the children away from the heater, always be carefully not to knock down the heater, which will break the 
glass tube and might cause injury.   
Do not move the appliance when in operation. 
After a long break of operation, the gas parts in the control box of the heater and the hose should be inspected 
for spiders, spider webs or other insects. 
Check the heater immediately if any of the following exists: 

1. There is smell of gas. 
2. The heater is not enough effective. 
3.  The  burner  makes  popping  noise  during  use  (a  slight  popping  noise  is  normal  when  the  burner  is 
extinguished 
after use).

If you smell gas, turn off the valve immediately. If smell persists, contact the dealer or gas supplier immediately. 
The hose with regulator assembly shall be stored in a safe place to avoid it’s accidental damage. 
Children and adults should be aware of the high surface temperature hazard, and should keep a safe distance 
away to avoid clothes burning or igniting. 
Young children should be carefully supervised when they are in the working area of the heater.
Clothing or other flammable material should not be hung from the heater, or placed on or near the heater. 
Do not obstruct the flow of combustion products.
Keep the ventilation opening of the cylinder enclosure free and clear of debris.
Do not obstruct the ventilation holes of the cylinder housing.
Shut off the valve of gas cylinder or the regulator before moving the appliance.
The tubing or the flexible hose must be changed within the prescribed intervals.
Use only the type of gas and the type of cylinder specified by the manufacturer.
In case of violent wind particular attention must be taken against tilting of the appliance.  

The appliance is for outdoor use only. Do not use 
indoors or in an enclosed area. 
Always maintain proper clearance from combustible 
materials, i.e. top 800mm and sides 650mm minimum

9

Содержание 16/DK1023A













Отзывы: