Toshiba ras-m07g3dv-e, Руководство по обслуживанию

Страница: 46 / 94

– 45 –
Setting Everyday Timer
• During the every day timer is activating, both arrows ( , ) are indicated.
Note:
• Keep the remote control in accessible transmission to the signal receiving unit;
otherwise, the time lag of up to 15 minutes will occur.
• The setting will be saved for the next same operation.
Set your preferred operation for future use. The setting will be memorized by the unit for
future operation.
1. Select your preferred operation.
2. Press and hold
for 3 seconds to memorize the setting. The P
mark displays.
3. Press : Operate the preset operation.
To automatically restart the air conditioner after the power failure (Power of the unit
must be on.)
Setting
1. Press and hold the TEMPORARY button on the signal receiving unit for 3
seconds to set the operation. (3 beep sound and OPERATION lamp blink
5 time/sec for 5 seconds)
2. Press and hold the TEMPORARY button on the signal receiving unit for 3
seconds to cancel the operation. (3 beep sound but OPERATION lamp does not
blink)
To operate at super low fan speed for quiet operation (except in DRY mode)
Press : Start and stop the operation.
Note: Under certain conditions, QUIET operation may not provide adequate cooling
due to low sound features.
For comfortable sleep, automatically control air flow and automatically turn OFF.
Press : Select 1, 3, 5 or 9 hrs for OFF timer operation.
Note: The cooling operation, the set temperature will increase automatically 1 degree/
hour for 2 hours (maximum 2 degrees increase). For heating operation, the set
temperature will decrease.
To protect bad smell caused by the humidity in the indoor unit.
1. If the button is pressed once during “Cool” or “Dry” mode, the fan
will continue to run for other 30 minutes, then it will turn off automatically. This
will reduce the moisture in the indoor unit.
If the time of “Cool” or “Dry” operation is less than 10 minutes, the self cleaning
operation is not performed.
2. To stop the unit immediately, press the more 2 times within
30 seconds.
1. Three-minute protection feature: To prevent the unit from being activated for
3 minutes when suddenly restarted or switched to ON.
2. Preheating operation: Warm up the unit for 5 minutes before blowing warm air.
3. Warm air control: When the room temperature reaches the set temperature, the fan
speed is automatically reduced and the outdoor unit will stop.
4. Automatic defrosting: Fans will stop during defrost operation.
5. Heating capacity: Heat is absorbed from outdoor and released into the room. When
the outdoor temperature is too low, use another recommended heating apparatus in
combination with the air conditioner.
6. Consideration for accumulated snow: Select the position for outdoor unit where it
will not be subjected to snow drifts, accumulation of leaves or other seasonal
debris.
Air conditioner operating conditions
Refer to the Installation Manual of the outdoor unit.
To separate using of remote control for each indoor unit in case of 2 air conditioners are
installed nearly.
Remote Control B Setup.
1. Press TEMPORARY button on the signal receiving unit to turn the air conditioner
ON.
2. Point the remote control at the signal receiving unit.
3. Push and hold button on the Remote Control by the tip of the pencil. “00”
will be shown on the display.
4. Press during pushing . “B” will show on the display and “00” will
disappear and the air conditioner will turn OFF. The Remote Control B is
memorized.
Note: 1. Repeat above step to reset Remote Control to be A.
2. Remote Control A has not “A” display.
3. Default setting of Remote Control from factory is A.
1
Press : Set the ON timer.
3
Press .
2
Press : Set the OFF timer.
4
Press button during the
( or ) mark flashing.
12
PRESET OPERATION
13 AUTO RESTART OPERATION
14
QUIET OPERATION
15 COMFORT SLEEP OPERATION
16
SELF CLEANING OPERATION (COOL
AND DRY OPERATION ONLY)
17 OPERATION AND PERFORMANCE
Outdoor Temperature Room Temperature
Heating Less than 28°C
Cooling 21°C ~ 32°C
Dry 17°C ~ 32°C
The unit does not operate. Cooling or Heating is abnormally low.
• The power main switch is turned off.
• The circuit breaker is activated to cut off
the power supply.
• Stoppage of electric current
• ON timer is set.
• The air filter (Locally procured) is
blocked with dust.
• The temperature has been set
improperly.
• The windows or doors are opened.
• The air inlet or outlet of the outdoor
unit is blocked.
• The fan speed is too low.
• The operation mode is DRY.
Temp.
Operation
18 TROUBLESHOOTING (CHECK POINT)
19
REMOTE CONTROL A-B SELECTION
A B