Toshiba nv-pack JTLI41 Скачать руководство пользователя | Manualshive

Страница: 38 / 58

background image

Chapter 4 Installation and Wiring

6F8C1601

24

4.4 Card Replacement

Replace the card in the following procedure.

1

Turn off the PC. Then turn off the AC power switch on the back of the PC and unplug the

power cord.

2

Pull out the cable of the TC-net I/O loop connected to the card by pinching the lock of the

connector with your fingers.

3

Refer to the procedure in "4.2 Card Mounting", remove the PC cover, the side cover on the

slot 50 side, and the fixing bracket on the slot 53 side, and remove the set screw on the

card panel.

4

Pull out the card vertically from the connector of the extended slot.

5

When preparing a new card, align the station address setting switch address with the

removed card.

6

Refer to the procedure in "4.2 Card Mounting", insert the new card vertically into the

connector of the extended slot, fix the panel of the card, insert the fixing bracket on the

side of the slot 53, the side cover on the side of the slot 50 and the PC cover.

7

Connect the cables of the TC-net I/O loop extracted in step 2, respectively.

Note



The extended card has a sharp protrusion. Protect your hand with a glove or other protective device

when pulling out the extended card.

«
...
36
37
38
39
40
...
»

Содержание nv-pack JTLI41



























































Отзывы:

Нет отзывов

Похожие инструкции для nv-pack JTLI41

Бренд: FabiaTech Страницы: 4

Transportation FiberinMotion

Бренд: Radwin Страницы: 122

Бренд: Queclink Страницы: 9

Бренд: Aewin Technologies Страницы: 86

Бренд: LevelOne Страницы: 3

Бренд: Acromag Страницы: 23

Бренд: Top Страницы: 21

Бренд: 8e6 Technologies Страницы: 94

Бренд: Uctronics Страницы: 12

Бренд: Wavtech Страницы: 8

EISBLOCK AURORA ACRYL GPX-N RTX 3070 VENTUS INCL

Бренд: Alphacool Страницы: 3

WSIL-1204-GT2-SFP2

Бренд: WAVESYS Страницы: 21

Бренд: Stepper Motor Canada Страницы: 7

Бренд: Epson Страницы: 97

Бренд: Epson Страницы: 159

ARM720T Core cpu

Бренд: Epson Страницы: 224

Бренд: Epson Страницы: 23

Бренд: StarTech.com Страницы: 9

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды