Toshiba MMD-AP0076BHPUL Скачать руководство пользователя страница 53 | Manualshive

Страница: 53 / 102

background image

Check code

Display of receiving unit

Typical fault site

Description of error

Outdoor 7-segment display

Indicator light block

Sub-code

Flash

Timer Ready

Operation

⎯

⎯

⎯

⎯

⎯

⎯

E01

E02

E02

Main

remote

controller

No master remote controller,
faulty remote controller
communication (reception)

Faulty remote controller
communication (transmission)

Signals cannot be received from indoor unit; master remote
controller has not been set (including two remote controller
control).

Signals cannot be transmitted to indoor unit.

Duplicated master remote
controller

Both remote controllers have been set as master remote
controller in two remote controller control (alarm and
shutdown for header unit and continued operation for
follower unit)

(Error detected by main remote controller)

Check code

Display of receiving unit

Typical fault site

Description of error

Outdoor 7-segment display

Indicator light block

Sub-code

Flash

Timer Ready

Operation

⎯

⎯

⎯

⎯

⎯

⎯

⎯

⎯

⎯

⎯

C05

⎯

⎯

C06

C12

P30

(Error detected by central control device)

TCC-LINK

central

control

No indication
(when main remote
controller also in
use)

Faulty central control
communication (transmission)

Faulty central control
communication (reception)

Multiple network adapters

Central control device is unable to transmit signal due to
duplication of central control device (AI-NET).

Central control device is unable to receive signal.

Multiple network adapters are connected to remote
controller communication line (AI-NET).

Blanket alarm for general-
purpose device control
interface

Device connected to general-purpose device control
interface for TCC-LINK / AI-NET is faulty.

As per alarm unit (see
above)

Group control follower unit
error

Group follower unit is faulty (unit No. and above detail
[

∗∗∗

] displayed on main remote controller)

Note:

The same error, e.g. a communication error, may result in the display of different check codes depending on the device that detects it.

Moreover, check codes detected by the main remote controller / central control device do not necessarily have a direct impact on air
conditioner operation.

- 53 -

«
...
51
52
53
54
55
...
»

Содержание MMD-AP0076BHPUL







































































































Отзывы:

Нет отзывов

Похожие инструкции для MMD-AP0076BHPUL

Бренд: Neffes Страницы: 20

Бренд: Dometic Страницы: 136

Бренд: Zibro Страницы: 22

ICE CHILLER TSU-M

Бренд: Baltimore Aircoil Company Страницы: 38

Бренд: Daewoo Страницы: 60

Бренд: AC Pro Страницы: 28

Бренд: Trotec Страницы: 16

Бренд: Carrier Страницы: 32

Бренд: Airtecnics Страницы: 22

Бренд: Linea 2000 Страницы: 104

AirHub Portable 113.0666.175

Бренд: FABER S.p.A. Страницы: 20

Бренд: Wow Страницы: 68

h2go purifier GLOBAL

Бренд: Aqua Research Страницы: 2

Бренд: Daikin Страницы: 84

Бренд: Altech Страницы: 48

Бренд: Ultravation Страницы: 2

Бренд: Trion Страницы: 4

Бренд: Convair Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды