Toshiba MMD-AP0076BHPUL Скачать руководство пользователя страница 33

Страница: 33 / 102

8-4. Test operation of indoor unit

Check function for operation of indoor unit (Functions at indoor unit side)

This function is provided to check the operation of the indoor unit singly without communication with the

remote controller or the outdoor unit. This function can be used regardless of operation or stop of the system.

However, if using this function for a long time, a trouble of the equipment may be caused. Limit using this

function within several minutes.

[How to operate]

1) Short-circuit CHK pin (CN71 on the indoor P.C. board).

The operation mode differs according to the indoor unit status in that time.

Normal time: Both float SW and fan motor are normal.

Abnormal time: Either one of float SW or fan motor is abnormal.

2) Restricted to the normal time, if short-circuiting DISP pin (CN72 on the indoor P.C. board) in addition to

short-circuit of CHK pin (CN71 on the indoor P.C. board), the minimum opening degree (30 pls) can be

set to the indoor PMV only.

When open DISP pin, the maximum opening degree (1500 pls) can be obtained again.

[How to clear]

Open CHK pin. While the system is operating, it stops once but automatically returns to operation after

several minutes.

• To exchange the indoor PMV coil, set the indoor PMV to Max. opening degree.
• For the detailed positions of CHK pin (CN71 on indoor P.C. board) and DISP pin (CN72 on indoor P.C. board),

refer to the indoor P.C. board.

Fan motor

Indoor PMV (*)

Louver

Drain pump

Communication

P.C. board LED

Short-circuit of CHK pin

Normal time

DISP pin short circuit

(H)

Min. opening degree (30 pls)

All ignored

Lights

DISP pin open

(H)

Max. opening degree (1500 pls)

All ignored

Lights

Abnormal time

Stop

Min. opening degree (30 pls)

All ignored

Flashes

- 33 -

Содержание MMD-AP0076BHPUL







































































































Результаты поиска

Содержание MMD-AP0076BHPUL

Отзывы:

Похожие инструкции для MMD-AP0076BHPUL

Бренды по названию

Популярные бренды

Toshiba MMD-AP0076BHPUL, Руководство по обслуживанию

Результаты поиска

Содержание MMD-AP0076BHPUL

Отзывы:

Похожие инструкции для MMD-AP0076BHPUL

Бренды по названию

Популярные бренды