– 20 –
EN
2. When you want to know position of the indoor unit using the address
•
To confirm the unit numbers in a group control;
[Procedure]
(Operation while the air conditioner stops)
The indoor unit numbers in a group control are successively displayed, and the corresponding indoor fan is turned on.
1
Push
+
buttons simultaneously for
4 seconds or more.
• Unit No
is displayed.
• The fans of all the indoor units in a group control are
turned on.
2
Every pushing
button, the indoor unit
numbers in the group control are successively
displayed.
• The firstly displayed unit number on number indicates
the address of the header unit.
• Only fan of the selected indoor unit is turned on.
3
Push
button to finish the procedure.
All the indoor units in group control stop.
▼
To confirm all the unit numbers from an arbitrary wired remote controller;
[Procedure]
(Operation while the air conditioner stops)
The indoor unit number and position in the same refrigerant line can be confirmed. A header unit is selected, the indoor unit
numbers in the same refrigerant system are successively displayed, and then its indoor unit fan is turned on.
1
Push the timer time
+
buttons simultaneously for 4 seconds or more.
Firstly, the line 1,
CODE No.
(Address Change) is displayed. (Select outdoor unit.)
2
Using
and
buttons, select the line
address.
3
Using
button, determine the selected line
address.
• The indoor address, which is connected to the
refrigerant system of the selected refrigerant system is
displayed and the fan is turned on.
4
Every pushing
button, the indoor unit
numbers in the same refrigerant system are
successively displayed.
• Only fan of the selected indoor unit operates.
To select another system address
5
Push
button to return to procedure
2
.
• The indoor address of another line can be successively
confirmed.
6
Push
button to finish the procedure.
3
1
2
1
TEMP.
ON / OFF
SET
TIME
TEST
FILTER
RESET
CL
SAVE
SWING/FIX
VENT
UNIT LOUVER
CODE No.
UNIT No.
R.C.
No.
E
D
O
M
T
E
S
R
E
M
I
T
FAN
SET DATA
SETTING
Operation procedure
1
→
2
→
3
End
End
VENT
TEST
TEST
TEST
5
6
1
3
2
4
TEMP.
ON / OFF
SET
TIME
TEST
FILTER
RESET
CL
SAVE
SWING/FIX
VENT
UNIT LOUVER
CODE No.
UNIT No.
R.C.
No.
E
D
O
M
T
E
S
R
E
M
I
T
FAN
SET DATA
SETTING
Operation procedure
1
→
2
→
3
→
4
→
5
→
6
End
SWING/FIX
SET
CL
TEST
Change of indoor address from wired remote controller
▼
To change the indoor address in individual operation (Wired remote controller : Indoor unit = 1 : 1)
or group control
(When the setup operation with automatic address has finished, this change is available.)
[Procedure]
(Operation while the air conditioner stops)
1
Push simultaneously
+
+
buttons for 4 seconds or more.
(The firstly displayed unit No. indicates the header indoor unit in group control.)
2
In group control, select an indoor unit No. to be changed by
button.
(The fan of the selected indoor unit is turned on.)
3
Using the setup temp.
/
buttons, set
to the CODE No.
4
Using the timer time
/
buttons, change the displayed setup data to a data which you want
to change.
5
Push
button.
6
Using the
button, select the unit No. to be changed at the next time.
Repeat the procedure
4
to
6
and change the indoor address so that it is not duplicated.
7
After the above change, push
button to confirm the changed contents.
8
If it is acceptable, push
TEST button to finish confirmation.
SET
CL
TEST
SET
TEST
3
5
8
1
4
2, 6, 7
CODE No.
ON / OFF
MODE
TEMP.
SETTING
SET DATA
VENT
UNIT LOUVER
FAN
TIMER SET
TIME
SAVE
SWING/FIX
SET
CL
FILTER
RESET TEST
UNIT No.
R.C
No.
Operation procedure
1
→
2
→
3
→
4
→
5
→
6
→
7
→
8
End
39-EN
40-EN
