Toshiba B-SX4 Series страница 75 Скачать руководство пользователя

Страница: 75 / 135

- 72 -

(28) Pre-peel-off process setting (PRE PEEL OFF)

• OFF: Pre-peel-off operation is not performed..

• ON: Pre-peel-off operation is performed.

NOTE: When the printer speed “10 ips” is specified, the pre-peel-off

operation is performed, even if it is set to OFF in this setting.

(29) Back feed speed setting (BACK SPEED)

•

STD:

ips

•

LOW:

ips

(30) MaxiCode specification setting (MAXI CODE)

• TYPE1:

Compatible with the current version

•

TYPE2:

Special

specification

The mode specified by the command may be different from the actual mode, depending on
the status of this parameter. Also, the data transmission method differs partly.
For details, refer to the B-SX4/SX5 External Equipment Interface Specification.

(31) Print head type setting (THERMAL HEAD)

B-SX4

B-SX5

• V2: Enhanced type TPH104R7

TPH128R5 or equivalent

•

V1:

Current

type

TPH104R2

TPH128R4

B-SX4: V2 type print head (TPH104R7 or equivalent) in or after September 2004

B-SX5: V2 type print head (TPH128R5 or equivalent) in or after November 2004

NOTE 1: Selecting the incorrect print head type may affect the

print quality or print head life.

NOTE 2: The enhanced print head (B-SX4: TPH104R7 or

equivalent, B-SX5: TPH128R5 or equivalent) has a

red line on the side. (See the picture on the left.)

Supplementary explanation

• When the [RESTART] and [FEED] keys are pressed at the same time, the display shows

the system mode menu.

• If the [RESTART] or [FEED] key is held down for 0.5 seconds or more when a parameter

is being set, the printer enters the repeat mode, in which the key is entered repeatedly.

• A changed parameter is stored in memory by pressing the [PAUSE] key.

FEED

RESTART

FEED

RESTART

FEED

RESTART

FEED

RESTART

Red line

Содержание B-SX4 Series








































































































































Результаты поиска

Содержание B-SX4 Series

Отзывы:

Похожие инструкции для B-SX4 Series

Бренды по названию

Популярные бренды

Toshiba B-SX4 Series, Руководство по ключевым операциям

Результаты поиска

Содержание B-SX4 Series

Отзывы:

Похожие инструкции для B-SX4 Series

Бренды по названию

Популярные бренды