Toshiba B-SX4 Series страница 132 Скачать руководство пользователя

Страница: 132 / 135

- 129 -

(12) RFID wireless power level

When the B-9704-RFID-U1-US/EU is installed.

0 to 255

Set the wireless power level from the RFID module. When the value is “0”, the power is the

weakest and when “255”, the power is the strongest. The factory setting is 251.

In the case of the B-9704-RFID-U1-EU-R, the factory default is 50.

When the B-SX704-RFID-U2 is installed.

18 to 26

When the value is “18”, the power is the weakest and when “26”, the power is the strongest.

The factory default is 20.

The optimal value is different depending on the tags used. Usually it is not necessary to change

this value but changing the value sometimes can increase the number of successful read/write

times.

(13) RFID AGC threshold setting

Available only when the B-SX704-RFID-U2 is installed.

0 to 15

Obtain the gain of the RFID tag, and when that gain is lower than the AGC threshold, tags

are considered as error tags even if a data write succeeds.

When the AGC threshold is se to “0”, all tags are writable. When set to 8, for example, only

tags with the AGC threshold level set to 8 or greater are writable.

The optimal value is different depending on the tags. The factory default is 0.

FEED

RESTART

• 255

• 252

• Initial value (251)

• 250

• 0

FEED

RESTART

• 26

• 18

• Initial value (26)

• 25

• 18

FEED

RESTART

• 15

• 1

• Initial value (0)

• 15

• 1

Содержание B-SX4 Series








































































































































Результаты поиска

Содержание B-SX4 Series

Отзывы:

Похожие инструкции для B-SX4 Series

Бренды по названию

Популярные бренды

Toshiba B-SX4 Series, Руководство по ключевым операциям

Результаты поиска

Содержание B-SX4 Series

Отзывы:

Похожие инструкции для B-SX4 Series

Бренды по названию

Популярные бренды