manualshive.com logo in svg

Toshiba B-SX4 Series, Руководство по ключевым операциям

Серия Toshiba B-SX4 представляет собой высококачественные принтеры этикеток с широким спектром возможностей. Узнайте, как использовать все функции этого устройства, загрузив бесплатное руководство по ключевым операциям на {веб-сайте}. Скачайте его сейчас, чтобы получить максимум от продукта.

Поделиться
Скачать
background image

 

- 37 -

6. SYSTEM MODE 

6.1  OUTLINE OF SYSTEM MODE 

In this mode, the printer self-test operation and parameter setting operation are performed.  

Described below is the key operation procedure performed regarding the system mode. 

z

System mode for service persons and system administrators (All system mode menus are 

available.) 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

While holding the [FEED] and [PAUSE] keys down, turn the power on. 

Maintenance counter/Various parameters printout,   
Printer self-test operation and results printout,   
Thermal head broken dots check 

Character code selection, Font “0” selection, Communication speed 

selection, Data length selection, Stop bit length selection, Parity selection, 

Transmission control method selection, Language selection for LCD 

messages, Setting for forward feed standby, Forward feed standby action, 

Setting for head-up operation in cut issue mode or for using the rewinder, 

Installed solenoid type setting, Ribbon saving system setting, Control code 

selection, Peel-off wait status selection, [FEED] key function setting, Kanji 

code selection, Euro code setting, Automatic head broken dots check setting, 

Centronics ACK/BUSY timing setting, Web printer function setting, Ribbon 

near end detection setting 

Reset process when the nInit signal is ON, Expansion I/O operation mode 

setting, Centronics operation mode setting, Plug-and-Play operation setting, 

Label end/ribbon end process setting, Pre-peel-off process setting, Back feed 

speed setting, MaxiCode specification setting, Print head type setting, 

System mode password operation setting, XML function setting (V4.4A only)

Feed fine adjustment, Cut position fine adjustment (or strip position 
fine adjustment), Back feed fine adjustment,   
X-coordinate fine adjustment, Print density fine adjustment (Thermal 
transfer/Direct thermal print mode), Ribbon motor drive voltage fine 
adjustment, Transmissive sensor manual threshold fine adjustment, 
Reflective sensor manual threshold fine adjustment,

 

Power OFF 

[RESTART] 

[FEED] 

[RESTART] 

[FEED] 

[RESTART] 

[FEED] 

[RESTART] 

[FEED] 

[RESTART] 

Parameter setting, 1-dot slant line printout, 3-dot slant line printout, 
Character printout, Bar code printout, Non-printing 
Automatic printout for the assembly process (Transmissive 
sensor/Reflective sensor), Factory pattern printout

 

Thermal head temperature sensor display, Open-air temperature 
sensor display, Reflective sensor display/adjustment,   
Transmissive sensor display/adjustments,   
Sensor status without paper, 

Ribbon end sensor status

 

<1>DIAG.

 

<2>PARAMETER SET

 

<3>ADJUST SET

 

Maintenance counter clear, Various parameters clear

 

<4>TEST PRINT

 

<5>SENSOR ADJ.

 

<6>RAM CLEAR

 

<7>IP ADDRESS

 

Printer IP address setting, Gateway IP address setting,   
Subnet mask setting, Socket communication port number setting, 
DHCP setting, DHCP client ID setting

 

Head-up adjustment for the process, Option check for the process 

[FEED] 

[RESTART] 

<8>BASIC

 

[FEED] 

[RESTART] 

<9>FOR FACTORY 

[FEED] 

[RESTART] 

[FEED] 

[RESTART] 

BASIC setting, BASIC file browser, BASIC trace setting 

Continued on the following page. 

Содержание B-SX4 Series








































































































































Отзывы:

Нет отзывов

Похожие инструкции для B-SX4 Series

Youjie 3300 Quick Start Manual preview
3300
Бренд: Youjie Страницы: 16
Tanca TL-120 Instruction Manual preview
TL-120
Бренд: Tanca Страницы: 22
U-Prox KeyPad User Manual preview
KeyPad
Бренд: U-Prox Страницы: 4
UniFlow MiCard PLUS-2 V2 Installation Manual preview
MiCard PLUS-2 V2
Бренд: UniFlow Страницы: 22
Nedap VP1006 Service Manual preview
VP1006
Бренд: Nedap Страницы: 27
Nedap TRANSIT-USA Installation Manuals preview
TRANSIT-USA
Бренд: Nedap Страницы: 59
Creator CRT-310-NR01 Manual preview
CRT-310-NR01
Бренд: Creator Страницы: 16
SAMSys SARS MP9112 Owner'S Manual preview
SARS MP9112
Бренд: SAMSys Страницы: 36
POSMicro Symbol DS3478 Product Reference Manual preview
Symbol DS3478
Бренд: POSMicro Страницы: 417
Dynex DX-CRMN1 - Mini Memory Card Reader/Writer User Manual preview
DX-CRMN1 - Mini Memory Card Reader/Writer
Бренд: Dynex Страницы: 20
Certgate AirID Mini Quick Start preview
AirID Mini
Бренд: Certgate Страницы: 5
RIOTEC LS6302J Programming Quick Manual preview
LS6302J
Бренд: RIOTEC Страницы: 2
RIOTEC FS5102N Programming Quick Manual preview
FS5102N
Бренд: RIOTEC Страницы: 2
M3 Mobile M3 ORANGE Snap-On User Manual preview
M3 ORANGE Snap-On
Бренд: M3 Mobile Страницы: 17
Magtek iDynamo 5 Installation And Operation Manual preview
iDynamo 5
Бренд: Magtek Страницы: 33
Datalogic MAGELLAN 8300 Quick Start Manual preview
MAGELLAN 8300
Бренд: Datalogic Страницы: 17
Feig Electronic OBID i-scan ID ISC.SPAD102 Installation Manual preview
OBID i-scan ID ISC.SPAD102
Бренд: Feig Electronic Страницы: 32
Bartec BCS 3800 User Manual preview
BCS 3800
Бренд: Bartec Страницы: 32

Бренды по названию

Популярные бренды

Загрузить еще бренды