Toshiba B-SX4 Series страница 27 Скачать руководство пользователя

Страница: 27 / 135

- 24 -

Print conditions:

• Print width:

Approximately 100 mm

• Sensor designation: None

• Print speed:

6 ips for B-SX4, 5 ips for B-SX5

• The print mode (thermal transfer/direct thermal) depends on the current setting.

• Data of 16 bytes is printed on one line.

• Data is printed, starting from the new data to the old data.

• Data pointed by the receive buffer write pointer is printed in bold type.

Size of receive buffer

B-SX4

B-SX5

RS-232C:

1 MB (Max. 65536 lines)

6 MB (Max. 393216 lines)

Centronics:

1 MB (Max. 65536 lines)

6 MB (Max. 393216 lines)

Network I/F:

1 MB (Max. 65536 lines)

6 MB (Max. 393216 lines)

BASIC1:

8 KB (Max. 512 lines)

BASIC2:

8 KB (Max. 512 lines)

USB:

1 MB (Max. 65536 lines)

6 MB (Max. 393216 lines)

RFID

8 KB (Max. 512 lines)

NOTES:

1. To print all of the receive buffer data, the label with the length below is required.

B-SX4

B-SX5

RS-232C:

198.2 m

1189.2 m

Centronics:

198.2 m

1189.2 m

Network I/F: 198.2 m

1189.2 m

BASIC1:

2 m

BASIC2:

2 m

USB:

198.2 m

1189.2 m

RFID

2 m

2. If an error occurs when printing the receive buffer dump, the printer displays an error

message, and stops. The error is cleared by pressing the [PAUSE] key, and then the

display is returned to the receive buffer dumping menu

“<4> DUMP MODE”. After the

error is cleared, data is not automatically reprinted.

5.10 BASIC EXPANSION MODE

It is possible to execute the BASIC expansion mode program in BASIC expansion mode under the

following conditions:

- The BASIC expansion mode program has already been loaded.

- The BASIC enable setting mode is selected.

The basic expansion mode ends when the basic expansion program is exited.

Содержание B-SX4 Series








































































































































Результаты поиска

Содержание B-SX4 Series

Отзывы:

Похожие инструкции для B-SX4 Series

Бренды по названию

Популярные бренды

Toshiba B-SX4 Series, Руководство по ключевым операциям

Результаты поиска

Содержание B-SX4 Series

Отзывы:

Похожие инструкции для B-SX4 Series

Бренды по названию

Популярные бренды