Toshiba B-SX4 Series страница 69 Скачать руководство пользователя

Страница: 69 / 135

- 66 -

(9) Setting for forward feed standby after an issue (FORWARD WAIT)

(10) Setting for forward feed standby action (FW/BK ACT.)

• MODE 1: Stops after 13.7-mm forward feed.

• MODE 2: Stops after 6-mm back feed and 3-mm forward feed. (Only

when the cut mode, thermal transfer, and feed gap sensor

are selected.) In other cases, the printer stops after 13.7-mm

forward feed.

(11) Setting for head-up operation in cut issue mode, or for using the rewinder (HU CUT/RWD.)

• OFF: Head-up operation is not performed/the rewinder is not used.

• ON: Head-up operation is performed/the rewinder is used.

When a cut issue is performed, this head-up operation setting takes
effect. When a batch issue is performed, the rewinder setting takes
effect.

NOTE: If the solenoid temperature is high when a cut issue is about to

be performed with the head lifted, the head may not be lifted.

FEED

RESTART

[FEED]

[RESTART]

FORWARD WAIT OFF

FORWARD WAIT ON

POSITION +0.0mm

POSITION +0.5mm

POSITION +5.0mm

POSITION -5.0mm

[PAUSE]

[FEED] [RESTART]

[FEED]

[RESTART]

POSITION -4.5mm

[FEED] [RESTART]

POSITION -0.5mm

[FEED] [RESTART]

• OFF: Not performed
• ON: Performed

Setting for the fine adjustment value for the
stop position after a forward feed standby:

-5.0 mm to +5.0 mm
+: Performs a longer length of a forward

feed, then stops.

-: Performs a shorter length of a forward

feed, then stops.

FEED

RESTART

[FEED]

[RESTART]

Содержание B-SX4 Series








































































































































Результаты поиска

Содержание B-SX4 Series

Отзывы:

Похожие инструкции для B-SX4 Series

Бренды по названию

Популярные бренды

Toshiba B-SX4 Series, Руководство по ключевым операциям

Результаты поиска

Содержание B-SX4 Series

Отзывы:

Похожие инструкции для B-SX4 Series

Бренды по названию

Популярные бренды