Toshiba B-SX4 Series Скачать руководство пользователя страница 70

Страница: 70 / 135

- 67 -

(12) Installed solenoid type setting (SOLENOID)

• TYPE 1: TDS-12C (wound with blue tape) is installed.

• TYPE 2: TDS-16A (stronger pull force type wound with black tape) is

installed.

NOTE: If this setting does not match the actually installed solenoid

type, ribbon saving function may not be able to work.

(13) Ribbon saving system setting (RIBBON SAVE)

• OFF:

The ribbon saving system is not used.

• ON (LBL): The ribbon saving system is used when the head lever

position is “LABEL”.

• ON (TAG): The ribbon saving system is used when the head lever

position is “TAG”.

NOTE:

If the ribbon saving system is used unless the ribbon saving
module has been installed, the ribbon may sag during
feeding/printing, and printing cannot be performed properly.
Be careful with this setting

(14) Control code selection (CODE)

[FEED]

[RESTART]

CONTROL CODE1 02

CONTROL CODE1 01

CONTROL CODE1 FE

CONTROL CODE1 00

CONTROL CODE1 FF

[FEED]

[RESTART]

[FEED]

[RESTART]

[FEED]

[RESTART]

[FEED]

[RESTART]

CODE AUTO

CODE ESC,LF,NUL

CODE { | }

CONTROL CODE1 1B

CODE MANUAL

CONTROL CODE2 0A

[PAUSE]

PEEL OFF STS OFF

CONTROL CODE3 00

[FEED]

[RESTART]

[FEED]

[RESTART]

[PAUSE]

[FEED]

[RESTART]

FEED

RESTART

FEED

RESTART

Содержание B-SX4 Series








































































































































Результаты поиска

Содержание B-SX4 Series

Отзывы:

Toshiba B-SX4 Series, Руководство по ключевым операциям, Страница: 70 / 135

Результаты поиска

Содержание B-SX4 Series

Отзывы: