Toro TimeCutter 74706 Скачать руководство пользователя страница 12

Страница: 12 / 56

Product Overview

g028411

Figure 4

Footrest

Gas-tank cap

Deflector

Smart Speed

™

lever

Height-of-cut lever

10.

Rear drive wheel

Motion-control lever

11.

Mower deck

Control panel

12.

Anti-scalp roller

Operator seat

13.

Front caster wheel

Engine

Controls

Become familiar with all the controls before you start
the engine and operate the machine.

Control Panel

g032603

Figure 5

Throttle control

Blade-control switch
(power takeoff)

Choke control

Key switch

Key Switch

The key switch, used to start and shut off the engine,
has 3 positions: O

, R

, and S

TART

. Refer to

Starting the Engine (page 21)

Throttle Control

The throttle controls the engine speed, and it has a
continuous-variable setting from the S

LOW

to F

AST

position (

Figure 5

Choke Control

Use the choke control to start a cold engine.

Blade-Control Switch (Power
Takeoff)

The blade-control switch, represented by a
power-takeoff (PTO) symbol, engages and
disengages power to the mower blades (

Figure 5

Motion-Control Levers

Use the motion-control levers to drive the machine
forward, reverse, and turn either direction (

Figure 4

Содержание TimeCutter 74706

























































Результаты поиска

Содержание TimeCutter 74706

Отзывы:

Похожие инструкции для TimeCutter 74706

Бренды по названию

Популярные бренды

Toro TimeCutter 74706, Руководство оператора

Результаты поиска

Содержание TimeCutter 74706

Отзывы:

Похожие инструкции для TimeCutter 74706

Бренды по названию

Популярные бренды