Toro TimeCutter 74706 Скачать руководство пользователя страница 31 | Manualshive

Страница: 31 / 56

background image

Recommended Maintenance Schedule(s)

Maintenance Service

Interval

Maintenance Procedure

After the first 8 hours

• Change the engine oil.

Before each use or daily

• Check the safety-interlock system.
• Clean and check the air-cleaner element.
• Check the engine-oil level.
• Clean the air intake screen.
• Inspect the blades.
• Inspect the grass deflector for damage.

After each use

• Clean the mower-deck housing.

Every 25 hours

• Grease all the lubrication points.
• Check tire pressure.
• Check the belts for wear or cracks.

Every 100 hours

• Clean the paper air-cleaner element (more often in dirty or dusty conditions).
• Change the engine oil (more often in dirty or dusty conditions).
• Replace or clean and gap the spark plug.
• Replace the in-line fuel filter.

Every 200 hours

• Replace the paper air-cleaner element (more often in dirty or dusty conditions).
• Change the engine-oil filter (more often in dirty or dusty conditions).

Before storage

• Charge the battery and disconnect the battery cables.
• Perform all maintenance procedures listed above before storage.
• Paint any chipped surfaces.

Important:

Refer to your engine owner's manual for additional maintenance procedures.

CAUTION

If you leave the key in the switch, someone could accidently start the engine and seriously
injure you or other bystanders.

Shut off the engine and remove the key from the switch before you perform any maintenance.

31

«
...
29
30
31
32
33
...
»

Содержание TimeCutter 74706

























































Отзывы:

Нет отзывов

Похожие инструкции для TimeCutter 74706

Бренд: Lawn-Boy Страницы: 20

Бренд: Lawn-Boy Страницы: 16

Бренд: Etesia Страницы: 24

Бренд: Brute Страницы: 44

MOW'N MACHINE FZ22-2

Бренд: Woods Страницы: 48

Бренд: Yazoo/Kees Страницы: 46

Бренд: Toro Страницы: 24

Бренд: Yazoo/Kees Страницы: 19

Бренд: Yard-Man Страницы: 6

Бренд: SANLI Страницы: 15

Бренд: Bad Boy Страницы: 36

Бренд: Eliet Страницы: 106

Бренд: Ariens Страницы: 6

Бренд: dormak Страницы: 24

Бренд: Cub Cadet Страницы: 867

Cruisematic 141-846H190

Бренд: White Outdoor Страницы: 32

Бренд: Craftsman Страницы: 48

Бренд: Craftsman Страницы: 48

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды