Toro TimeCutter 74706 Скачать руководство пользователя страница 33

Страница: 33 / 56

Engine Maintenance

Engine Safety

•

Shut off the engine before checking the oil or
adding oil to the crankcase.

•

Keep your hands, feet, face, clothing, and other
body parts away the muffler and other hot surfaces.

Servicing the Air Cleaner

Service Interval:

Before each use or daily—Clean

and check the air-cleaner element.

Note:

Service the air cleaner more frequently (every

few hours) if operating conditions are extremely dusty
or sandy.

Removing the Air-Cleaner Paper
Element

Park the machine on a level surface, disengage
the blade-control switch (PTO), and engage the
parking brake.

Shut off the engine, remove the key, and wait
for all moving parts to stop before leaving the
operating position.

Clean around the air-cleaner cover to prevent
dirt from getting into the engine and causing
damage.

Loosen the hose clamp and remove the paper
element (

Figure 29

g207139

Figure 29

Cover

Hose clamp

Paper element

Servicing the Paper Air-Cleaner
Element

Service Interval:

Every 100 hours—Clean the paper

air-cleaner element (more often in
dirty or dusty conditions).

Every 200 hours—Replace the paper air-cleaner
element (more often in dirty or dusty conditions).

Clean the paper element by tapping it gently to
remove dust.

Note:

If it is very dirty, replace the paper

element with a new one.

Inspect the element for tears, an oily film, or
damage to the rubber seal.

Replace the paper element if it is damaged.

Important:

Do not clean the paper filter.

Servicing the Engine Oil

Engine-Oil Specifications

Oil Type:

Detergent oil (API service SF, SG, SH, SJ,

or SL)

Crankcase Capacity:

1.8 L (61 fl oz); without filter;

2.1 L (70 fl oz) with filter

Viscosity:

See the table below.

g017470

Figure 30

Checking the Engine-Oil Level

Service Interval:

Before each use or daily

Note:

Check the oil when the engine is cold.

Important:

If you overfill or underfill the engine

crankcase with oil and run the engine, you may
damage the engine.

Park the machine on a level surface, disengage
the blade-control switch (PTO), and engage the
parking brake.

Содержание TimeCutter 74706

























































Результаты поиска

Содержание TimeCutter 74706

Отзывы:

Похожие инструкции для TimeCutter 74706

Бренды по названию

Популярные бренды

Toro TimeCutter 74706, Руководство оператора

Результаты поиска

Содержание TimeCutter 74706

Отзывы:

Похожие инструкции для TimeCutter 74706

Бренды по названию

Популярные бренды