Toro TimeCutter 74706 Скачать руководство пользователя страница 39

Страница: 39 / 56

Charging the Battery

Service Interval:

Before storage—Charge the battery

and disconnect the battery cables.

Remove the battery from the chassis; refer to

Removing the Battery (page 38)

Charge the battery for a minimum of 1 hour at
6 to 10 A.

Note:

Do not overcharge the battery.

When the battery is fully charged, unplug
the charger from the electrical outlet, then
disconnect the charger leads from the battery
posts (

Figure 40

g000538

Figure 40

Positive (+) battery post

Red (+) charger lead

Negative (–) battery post

Black (–) charger lead

Installing the Battery

Position the battery in the tray (

Figure 39

Using the fasteners previously removed, install
the positive (red) battery cable to the positive
(+) battery terminal.

Using the fasteners previously removed, install
the negative battery cable to the negative (-)
battery terminal.

Slide the red terminal boot onto the positive
(red) battery post.

Secure the battery with the hold-down (

Figure

Lower the seat.

Servicing the Fuses

The electrical system is protected by fuses. It requires
no maintenance; however, if a fuse blows, check the
component/circuit for a malfunction or short.

Fuse type:

•

Main—F1 (30 A, blade-type)

•

Charge Circuit—F2 (25 A, blade-type)

Remove the screws securing the control panel
to the machine.

Note:

Retain all fasteners.

Lift the control pane up to access the main wire
harness and fuse block (

Figure 41

To replace a fuse, pull out the fuse to remove
it (

Figure 41

g014921

Figure 41

Main (30 A)

Charge circuit (25 A)

Return the control panel to its original position.

Note:

Use the screws removed previously to

secure the panel to the machine.

Содержание TimeCutter 74706

























































Результаты поиска

Содержание TimeCutter 74706

Отзывы:

Похожие инструкции для TimeCutter 74706

Бренды по названию

Популярные бренды

Toro TimeCutter 74706, Руководство оператора

Результаты поиска

Содержание TimeCutter 74706

Отзывы:

Похожие инструкции для TimeCutter 74706

Бренды по названию

Популярные бренды