background image

Safety

Improper use or maintenance by the operator or owner
can result in injury. To reduce the potential for injury,
comply with these safety instructions and always pay
attention to the safety-alert symbol (

Figure 2

), which

means

Caution

,

Warning

, or

Danger

—personal

safety instruction. Failure to comply with the
instruction may result in personal injury or death.

DANGER

There may be buried power, gas, and/or
telephone lines in the work area. Digging into
them may cause a shock or an explosion.

Have the property or work area marked for
buried lines and do not dig in marked areas.
Contact your local marking service or utility
company to have the property marked (for
example, in the US, call 811 or in Australia,
call 1100 for the nationwide marking service).

Safe Operating Practices

This product is capable of amputating hands and feet.
Always follow all safety instructions to avoid serious
injury or death.

WARNING

Engine exhaust contains carbon monoxide,
an odorless poison that is fatal if inhaled.

Do not run the engine indoors or in an
enclosed area.

Training

Read the

Operator's Manual

and other training

material. If the operator(s) or mechanic(s) cannot
read this information, it is the owner's responsibility
to explain this material to them.

Become familiar with the safe operation of the
equipment, operator controls, and safety signs.

All operators and mechanics should be trained.
The owner is responsible for training the users.

Never let children or untrained people operate or
service the equipment. Local regulations may
restrict the age of the operator.

The owner/user can prevent and is responsible
for accidents or injuries occurring to himself or
herself, other people or property.

Preparation

Before using the machine, have the area marked
for underground utilities and do not use the
machine in marked areas.

Evaluate the terrain to determine what accessories
and attachments you need to properly and
safely perform the job. Use only the accessories
and attachments that are approved by the
manufacturer.

Wear appropriate clothing including gloves, eye
protection, long pants, substantial slip-resistant
footwear, and hearing protection. Tie back long
hair and do not wear loose clothing or loose
jewelry.

Inspect the area where you will use the equipment
and remove all objects, such as rocks, toys, and
wire, that the machine could throw.

Check that the operator's presence controls, safety
switches, and shields are attached and functioning
properly. Do not operate the machine unless they
are functioning properly.

Fuel Safety

Use extra care when handling fuel. It is flammable
and its vapors are explosive.

Extinguish all cigarettes, cigars, pipes, and other
sources of ignition.

Use only an approved fuel container.

Do not remove the fuel cap or fill the fuel tank
while the engine is running or hot.

Do not add or drain fuel in an enclosed space.

Do not store the machine or fuel container where
there is an open flame, spark, or pilot light, such
as on a water heater or other appliance.

If you spill fuel, do not attempt to start the engine;
avoid creating any source of ignition until the fuel
vapors have dissipated.

Operation

Use your full attention while operating the
machine. Do not engage in any activity that
causes distractions; otherwise, injury or property
damage may occur.

Clean debris from the hydraulic lift, drives,
mufflers, and engine after each use to help
prevent fires.

Park the machine on a level surface, lower the
hydraulic lift, disengage the hydraulics, engage the
parking brake (if applicable), shut off the engine,
and remove the key before leaving the operator's
position for any reason.

Do not touch parts that may be hot from operation.
Allow them to cool before attempting to maintain,
adjust, or service the machine.

Never run an engine in an enclosed area.

Operate the machine only in good light, keeping
away from holes and hidden hazards.

4

 

Содержание STX-26

















































Отзывы: