background image

This product complies with all relevant European
directives, for details please see the separate product
specific Declaration of Conformity (DOC) sheet.

Introduction

The Reelmaster Transport frame, when equipped with
reel cutting units and mounted behind a tow vehicle is
intended to be used by professional, hired operators in
commercial applications. It is designed for pulling reel
cutting units to cut grass on well-maintained lawns
in parks, sports fields, and on commercial grounds.
Using this product for purposes other than its intended
use could prove dangerous to you and bystanders.

Read this information carefully to learn how to operate
and maintain your product properly and to avoid
injury and product damage. You are responsible for
operating the product properly and safely.

Visit

www.Toro.com

for more information, including

safety tips, training materials, accessory information,
help finding a dealer, or to register your product.

Whenever you need service, genuine Toro parts, or
additional information, contact an Authorized Service
Dealer or Toro Customer Service and have the model
and serial numbers of your product ready.

Figure 1

identifies the location of the model and serial numbers
on the product. Write the numbers in the space
provided.

Important:

With your mobile device, you can

scan the QR code on the serial number plate (if
equipped) to access warranty, parts, and other
product information.

g316643

Figure 1

1.

Model and serial number location

Model No.

Serial No.

This manual identifies potential hazards and has
safety messages identified by the safety-alert symbol
(

Figure 2

), which signals a hazard that may cause

serious injury or death if you do not follow the
recommended precautions.

g000502

Figure 2

Safety-alert symbol

This manual uses 2 words to highlight information.

Important

calls attention to special mechanical

information and

Note

emphasizes general information

worthy of special attention.

© 2020—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420

2

Contact us at www.Toro.com.

Printed in the USA

All Rights Reserved

 

Содержание Reelmaster 33455





























Отзывы: