background image

Always inspect the hitch and coupling for wear.
Do not tow the machine with damaged or missing
hitches or couplings.

Avoid sudden stops and starts. This can cause
skidding or jack knifing. Smooth, gradual starts
and stops will improve towing.

Avoid sharp turns to prevent rolling.

Chock the wheels to while parked to prevent
movement.

Raising the Mowers to the
Transport Position

Note:

Before moving to the next mowing area, make

sure that all mowers are in the full transport position.

1.

Remove hairpins securing the transport strap to
the center frame channel and lift off the strap
(

Figure 19

).

g012727

Figure 19

Unit shown with 5-7 Conversion Kit installed

1.

Hairpins

2.

Transport straps

2.

Mount the transport strap to the mounting pins
on the lift arms and secure it with hairpins
(

Figure 20

).

g012734

Figure 20

Unit shown with 5-7 Conversion Kit installed

1.

Mounting pins on lift arms

3.

Remove the hairpin securing the lockup pin to
the center cylinder rest (

Figure 21

).

g012765

Figure 21

1.

Lockup pins

3.

Cylinder rest

2.

Hairpin

4.

Slide the lockup pin through the holes in the
lockup bracket and secure it with a hairpin
(

Figure 22

).

18

 

Содержание Reelmaster 33455





























Отзывы: